BlyilyB Motorcycle Blinkers Indicator Turn Signal Amber Flowing Sequential Universal Lamp (Pack of 4)

Excellent upgrade for an older bike. Upgrading to led you’ll need resistors i think ppl call them canbus unit. Easy to install and have been working for over 6 months. The resistor is sittin next to the turn signal in the picture.

I'm not sure if these are because they're new, but I hooked them up to a 12 volt battery directly and they flash in sequence perfectly. I was very happy and surprised because I'm adding these to my ebike and it has no flasher circuit. It's based on other reviews I expected them to just blink on and off like a normal car flasher which would have been more than fine with me as I wasn't really that concerned with it being in sequence. But to my surprise and joy it does flash in sequence and it is also pretty bright. I have not installed them on the bike yet as I'm waiting for some brackets and wiring I need to create the connections but if they all work like this I will be extremely happy with the units. They are also flexible so once they are mounted if I run into a branch or something or hit it with my leg it has a pretty good amount of flex to it so it will not break so easily. I will try to update this review with a video once it's all set up. ______ Update: I was able to get them installed on the E-bike and they work great, though I did end up just swapping them out for another version that is about twice as bright and has a larger lens as I wanted to make sure that they were as visible as possible, especially in the daytime. But these are still very good and blink a little faster than the newer ones which I like to.

A bit flimsy so don’t tighten the mounting bolt too tight. They work well, and look sleek! Great mod for my Icebear Maddog 150cc Gen 1. I soldered the wires in as the crimps are a bit unstable when you start manipulating the wires for zipping to the frame and wiring harness. Good decision if you choose these!

They work great

Great price and fast shipping and work great on my scooter

Didn't work whatsoever tried all 4 even had my mechanic try to install and Google around in case I messed up does not work dont bother. Mechanic said even for that price I was ripped off.

After a year they still work. You do need an led relay or your signals will blink very rapidly

First off, understand what it is you're considering here...I bought 4 of these for FOURTEEN DOLLARS! That's less than $5 a signal which is ridiculous cheap, but that comes at a price. I've owned 17 or 18 motorcycles and turn signals are always a must have for upgrades as factory ones just look silly. Dont get me wrong, these look amazing!!!! Put them on the night before a 300-400mi ride and got lots of compliments on them...but I did end up having to duct tape one in place as the adhesive that held the metal threads into the rubber stock of the housing let go and it was dangling there lol. Have tried some black silicone sealant and that didn't hold, tried some contact cement and that didn't hold. Going extreme next as I love the look of these and am bound and determined to keep them on the bike. Will try a two part glue next and a small hose clamp (black paint pen will make the hose clamp dissapear) and red loctite on the threads will keep the nut in place. Also to note, I put these on my 2018 KTM 1290 Super Duke R and did not need an led blinker relay, some reviewers have noted needing the cheap relay to get them fully cycle.

These lights are a lot smaller than incandescant turn signals but crazy bright. Depending on the bike, you might need to replace your Indicator Relay. On my 2012 XT250, the lights did not work at all when I first connected them. I had to locate and replace the relay box near the battery and then they worked perfectly. LED relay cost around $30 at a motorcycle shop.

Los productos son lo que se estaba buscando.

Alumbran muy bien, más que las originales, no se cuánto duren, pero de momento van bien.

As described, very fast delivery, if you have after market fender eliminator you may need to do a little dremel work on adaptor plates to get them to fit. I have not had a chance to put front blinkers on yet. They look good and work well, nice and bright.

nice and easy to install works perfectly. (you might need a led flasher)