Thermal Grizzly - PhaseSheet PTM (50x40mm) - High Performance Thermal Pad with Phase Change Material | Durable, Non-Conductive | For Cooling CPU, GPU, Electronics

25年12月時点で、メーカー→代理店の正規ルートで入手できる唯一のPTMじゃないでしょうか？ 肝心のパフォーマンスについてですが、もう素晴らしいの一言です。 CPU：9800X3D、クーラー：360mm簡易水冷の環境で、グリスは某あるてぃめいとな美少女グリスを使用していましたが、このphase sheetに変えて見たところCinebench R23上で−5℃程度差が出ました。（グリスの方も塗布から半年も経ってなく粘性がしっかりと残っている状態だったのでコンディションは良好でした） 検証ガチ勢ではないので、室温などの影響も多少あるでしょうが、それでも冷却効率に差があることは確実かと。 1枚2400円と値段だけみれば高く感じますが、アリエクガチャの心配がない、グリスより冷える、定期メンテナンスから解放されることを思えば全然その価値はあると思います。というかグリスちまちま買い足す方がコスパ悪くね？と思います。 取り付け時のコツですが、冷蔵庫であらかじめ冷やしておくことです！ これによりフィルムを剥がす際に本体が破れてしまうリスクを減らせます。自分は10分弱冷やしましたが、特にトラブルなくスムーズに貼り付けできました。

Cured/fixed my thermal issues on my INTEL NUC PC!

良い商品だろうがなんだろうが保護シートを剥がしたら一緒に剥がれてちぎれるのは論外

Great stuff, it works quite well. A little tough to peel off the protective sheets thou. The trick I found was to peel off the harder to remove side first mostly to loosen it. Then peel the other side a bit at the opposite corner to loosen it and then you should be able to apply it without issues. I tested it against Arctic Silver 3 which is ancient and it was a lot better.

Decided to try this instead of Honeywell one because that one is difficult to find. In terms of application and ease of use it's pretty much the same as Honeywell. And I suppose performance wise as well because it's been quite some time since I applied it and my gaming laptop has not thermal throttled or even needed to ramp up fans a lot. Overall it's quieter, colder and stutter free. I highly recommend to ditch normal compounds and get this instead. Follow instructions carefully and remember to clean every part of your heatsink and cooling system properly because using this.

Listen, this stuff is great and easy to install (put it in the fridge for 2 hours, cut to size, peel off the film with tweezers and slap it down). The thermal performance was slightly better than Arctic MX-4 as I'm not using direct-to-die cooling, but I mainly bought this for the longevity. I must warn you, however, that if you do decide to replace your CPU cooler at some point like me, this stuff is not the soft flexible material that that it is pre-application. Once it's gone through some heat cycles it turns into CEMENT. Yanked my AM4 CPU right out of the socket even after running Prime95 for 30 mins prior to removal. I had to use a heat gun directly on the heatsink just to get the PhaseSheet soft enough to pry the CPU off. Thankfully no damage to the pins, but it's something to bare in mind. If you plan on keeping your CPU cooler for 5+ years, and want a very effective thermal solution where you never need to repaste, BUY THIS, IT'S GREAT. If you foresee yourself changing your CPU or CPU cooler anytime soon, STEER CLEAR.

It's quite expensive for the size you get. Put it in the fridge before trying to cut it into shape and then it'll be easy to cut into shape. It's not that easy to apply if you're cutting a custom size. It works very well, my temps went down by 10 degrees compared to high performance thermal paste. The size is as advertised.

Excellent getting 30c to 70c on hotspot watting for inbeding on a rx9060tx gpu 30c to 45c have got a few heat sinks an the back plate thou.