Cord Hider Wall for 4-7 Wires, 48in Cable Management Kit, X-Large Cord Organizer Wall, TV Cable Hider Wire Hider for Wall Hide Cords Wall Mounted TV, Cable Raceway Black 3X L16in, W1.5in H0.8in

Great, easy to use, self-adhesive cord cover. The small size will fit one flat cord (like for a space heater) or two small round cords (like for a phone charger). It looks nice and baby no longer has any interest in playing with the baby monitor cord. I'm not sure why the instructions say to use scissors or a utility knife to cut it - I tried and these were definitely not the right tools - but it cut very nicely using a hacksaw and some sandpaper to go around some tricky rounded corners.

Really works great and looks awesome with my wall mounted speakers. Beats trying to fish speaker, wires through the walls and making a bunch of holes. I have enough left over to run the wires horizontally above the baseboard if I ever get to that.

Simple and sleek. I'd by again, but their instructions on cutting them are not great. You are much better off using a miter saw or something to give it a clean cut. Cutting with scissors like they suggest always ends up with a "messy" looking edge. Otherwise, a decent product.

I bought these for custom modifications to industrial style book shelves I bought. I added 1" metal angle at the back of the shelves and 3/4" in the front to support the thin 3/4" shelves to prevent sagging under the weight of heavy books. I added strip lights under the front angle and made a custom wiring harness to distribute power to each shelf. I needed these tracks to be thin enough to fit within and behind the 1" metal frame and black to match. These not only hide the red wire of the red/black wire I was using but it also keeps the wire tucked away and prevents it from sagging. These cut easily and adhere well. The only problem is that the waxed paper that covers the adhesive strip can start to rip when taking it off so I used tweezers to grab the ripped pieces to remove them for full adhesion. The pics show the completed project and a closeup of the channel concealing the wiring

Worked great to hide a single subwoofer cable. I mounted it around a large double door frame. It's hardly noticeable. I thought each piece was going to be longer, although It was described perfectly accurately. So I had to install quite few pieces. It's a bit challenging to remove/reinstall the covers which snap on very tightly. Also, the adhesive backing didn't peel off cleanly, usually tearing and leaving long thin sections of backing still on the mount. After the fifth one I installed, I began to get the hang of it, very carefully removing the backing by wiggling it left and right. That seemed to work best.

Exactly the size I needed to hide a single cable. I have a swinging microphone boom arm on my desk that had Velcro straps holding the cables. Kind of messy, not a good look. So I wanted cable management that was thin enough to blend in with the arm. This is the perfect size and almost looks like it was part of the arm to begin with. Was easy to cut, and easy to stick on.Word of advice though, rather than trying to “pull” the top and bottom apart, just “slide” them apart long-ways. You’ll save your fingernails. Then they snap back together very easily and hold tight.Now I’m looking around at what other cables I could possibly hide with these things. Good quality, highly recommend.

Easy installation, just need a level to make it straight, alcohol, and towel to wipe the wall for the double sided tape to stick well. 15 minutes to install.

This is a really clean way to hide your cables around your room. I moved my desk to the other side of the room and I needed the ethernet cable to wrap around half of the room. I had to get it around 2 corners so I needed to cut a few pieces to fit the corner nicely. The directions mention I can cut with a utility knife or sharp scissors but the plastic is actually very hard and thick in which I used a rotary tool to cut the corner parts nicely.

This cable cover is so sleek and so clean that you can't even tell it's not just part of the white baseboard trim. Easy to install, sticks well to the wall, and puts the cord out of sight.

Good

I've been using these kinds of wire hiders for a while now, and this particular brand is just as great. I used it primarily to hide my ethernet cables without drawing too much attention to them. Bear in mind that this will probably only handle ONE rounded ethernet cable. It's very tiny. However...you WILL be able to easy lay down TWO flat-corded ethernet cables without any issues. That's the way to go.

Looks great. Very easy to install. Quality is good, seems/joints are invisible. Would buy again.

Great product, fast delivery dist the job it's was intended to do very well.