- Shorty Headers for LS Swaps 304 Stainless Steel Exhaust Headers 2.5 Inch 3 Bolt Collectors Fits 4.8L 5.3L 5.7L 6.0L 6.2L LS1 LS2 LS3 LS6 V8 S10 C10 K10 Truck Includes Header and Collector Gaskets

Nice fit seems to be quality stainless steel time will tell

Very nice welds and fitting.

Quick shipping. The headers lined right up and the fitment was perfect First two sets I ordered from other sellers would not even align the bolt holes. Would buy from them again

Great so far came fast

As stated, will not fit a K10 pickup if you have a standard transmission. Will fit an automatic as there is no clutch linkage in the way

Very nice quality and fitment.

Great quality, welds look perfect. Fits great on my ls 6.0 swapped 1978 chevy squarebody

5 Stars for being as advertised. Rating based on value. What I liked: -Value. I can't say enough to justify the bang for buck your getting here. These headers at 179.77CAD (at time of review) are very inexpensive. They are stainless steel headers, I ran a 60lb rare earth magnet over them and there was no attraction. -Flanges are thick. The flanges are fairly thick so I don't think I'll have any issues there. I do know some less expensive headers come with thinner flanges but these look to be correctly sized. -The upstream O2 sensor bungs come with a bolt to cap it off if your vehicle pre dates this sort of thing. Does not come with any high temp thread sealant though. What I didn't like: -Blemishes. There are a number of finishing scratches and pits, nothing too serious and nothing I would complain about seeing as the initial cost is so low. Overall these are very inexpensive Stainless Steel shorty headers which have a very generic design. Very common style which are a dime a dozen. As for gaskets, I will pick up high quality gaskets separately because I don't want any exhaust leaks and do want some piece of mind. The money saved on the headers leaves a lot of room to improve the quality of the gaskets and anything else I may need.

This set of shorty headers for LS swaps is the set you need to start your performance exhaust system from the engine block The kit includes two shorty headers made out of a great gauge stainless steel with the necessary gasket to fit them on your block , the welds are on point and there is no flaw into the finish of the polish this also includes the bolt to install onto your LS block You also get a pair of short tubes with oxygen sensor plugs that are closeable by 2 bolt with seals if you don't need it and a gasket and bolt to bring all of these together this tube is also meant to weld with the rest of your exhaust setup , that is nice that they thought about it ! Fitment is 100% correct , nothing negative to mention as everything went well on the installation process This set is really awesome for the price they sell , you get more value for your money and over that you get great quality to go further into your project car !

I’ve spent a few days working with this set and it's been a relatively good experience. The 304 stainless steel feels thick in my hand compared to others I've held in the past. For the price range it feels to be a good build quality. The side welds and flanges look pretty seamless, which gives me piece of mind it's out together well to be ro ust for a longastinv LS swap job. As for the fitment, it was perfect for a 5.3 LS swap, with most areas lining up nicely, and the included gaskets were better than expected and sealed up without leaks. There was some minor adjustments required here luckily i had the right tools. Performance-wise, they seem to be a nice upgrade over stock manifolds, with quicker responding throttle action and improved exhaust flow. The only downside I've noticed which is not a big deal is that the fitment range can be a bit tight in some chassis, so expect minor adjustments depending on the swap. I had to do some adjustments to make it fit right in my build. For the price range this is a good value!

This is a seriously impressive set of stainless steel exhaust headers for auto enthusiasts doing LS engine swaps. Being an enthusiast myself, I found that this set of headers offers a compelling value for the money based on the build/materials quality and included gaskets/mounting bolts. All of the welds upon close inspection are nicely done - clean and uniform without notable imperfections. The materials quality, flanges, runners, and accompanying gaskets and hardware are all nicely done, and offer a level of quality that one might expect from a set of headers costing significantly more. As mentioned, all welds were closely examined and very clean - right down to the 02 bungs. It's really nice to see this value at the price point, and it's "ready to go" out of the box with gaskets and mounting hardware. This would be a compelling set for an enthusiast doing an LS swap on a tight budget looking for a quality kit that doesn't skimp on quality - I'd rate this as a highly recommended set of headers given the 304 stainless steel construction, included gaskets, and top notch build.

Nice headers, while they're not the most absolutely perfect and pretty headers I've ever seen, they're plenty good and well enough made overall. This is also reflected decently enough in the price, which is totally fair enough for what you're getting. Looking at them in the open there's some small details, like the welds could be a little nicer visually, but to be fair that stuff isn't all that visible once they're installed in an engine compartment, so I can't say that I have any real complaints about that. As far as what matters, once they're installed they look great. Build quality seems pretty nice overall, while the welds aren't the best visually, they're not terrible and there's no indication that they would be inadequate or poor quality in general. Looking up the tubes I don't see any sign of 'sugaring', to indicate any weld problems either. Nice set with everything important included.