Geekworm X1002 PCIe to M.2 HAT NVMe SSD PIP PCIe Peripheral Bottom Board for Raspberry Pi 5 Support M.2 2230/2242/2260/2280 SSD

Some reviewers, no small number of them have had issues receiving the incorrect screws, I did NOT have that problem. My NVME base was purchased with the corresponding metal case so this review is kind of for both of them.The NVME base was purchased in a pinch when shippment was delayed in a time sensitive setup for a Pimoroni base I ordered. I now have both and can compare them. Assuming the packaging bugs have been worked out, honestly the Geekworm BASE is much nicer. The factory pre-fitted and threaded risers are a wonderful item to simplify installation.There is NO documentation that comes in the box so forget about that, but if you look at the pics here on how they are setup you can figure it out, simply put the NVME goes to the bottom, not the top, the risers go between the Pi and the base.Attach the NVME, attach the ribbon cable, then screw it all together, Your hardware assembly is done.Boot to an SD card with Raspberry Pi OS on it, and run Raspberry Pi imager and write your OS to the NVME,Follow the setup instructions from Explaining Computers youtube page on the software setup to get the NVME going, I have mine set to PCIe Gen 3 and it is plenty fast.The complaints about them not working or wrong screws seem to be from right after it was introduced and I am going to assume those are just issues with early production items. The one I got went together super easy, and super solid.The NVME mount itself has a threaded standoff unlike the Pimoroni, which makes mounting the NVME much easier, although it only seems to support the M.2 2280 NVMEs, but that is what I wanted to use anyway.The whole thing Pi, Cooler, NVME base and NVME fit neatly into the Geekworm case, and through the risers that come with the case which are slightly shorter than the ones that come with the NVME base, the alignment is perfect, screwed together through the bottom of the case and it is solid as a brick.Complaints about WiFi interference with the case are not something I have noticed. WiFi is good and strong, bluetooth pairs up just fine.No interference with the ribbon cable to the case, although I did flatten the cable up against the Pi itself as much as possible without damaging it before assembling to the Pi. I also have a Logitech Unifying receiver / keyboard / mouse and notice no radio / connectivity issues with either.The ribbon cable installs MUCH easier and is less fiddly than the one that came with the Pimoroni.I do not regret either purchase, and they will serve my purposes very well indeed. But if I had it to do over again, I would have gone with 2 of these Geekworm bases and cases and been done with it straight out.Again at least with the units I received, they are spot on.SPECS of my build.Raspberry Pi 5 8GBRaspberry Pi 5 Official active coolerRaspberry Pi 5 Official power supply (USA)Geekworm X1002 NVME baseGeekworm P580 caseCrucial P3 Plus 2TB M.2 NVME SSDLogitech Unifying receiver.Summary. All of the issues I have read about in other reviews did NOT show up with my device. Installation was super easy, build quality is above and beyond what is to be expected at this price point. Functionality at least paired with my chosen hardware is perfect.Only time will tell about long term durability / reliabiliity, but if my initial impressions are correct, this will hold up and be a good performer.

Installed Ubuntu 24.04.1 LTS 64bit, Using a generic USB to SSD enclosure and the raspberry pi imager, this worked without any modifications to any settings, configuration files or boot order on the pi or OS. Choose "other general purpose OS" in the pi imager to install Ubuntu to the SSD.Installed X1002 using the provided cable and hardware to the Pi5 8GB, then installed the NVME SSD with the Ubuntu Image on it. Booting will then brings you into the OS setup wizard.Once in the OS, updated to PCIE Gen 3 in the conifg.txt as per the directions on the support page listed in the description and there are no stability issues to report.Have tested installation on 6 different major brands of NVME SSD with no issues in recognizing the drive and boots to the OS without intervention.It is great the board mounts on the bottom with the SSD facing down, The PCB acts as heat shield if your project requires excessive read and writes, but if you are worried about heat from your SSD buy or print a case that mounts the pi on its side with vents on the top. Using the two push pins to power the unit from the underside of the GPIO gives it a clean install, just make sure they contact correctly and you boards are flush to each other. The mounting solution using the long screws to secure the two boards together that then protrude out the bottom side (same side as SSD) to install the risers works great too.The performance overall using the SSD is noticeably fast and is worth the ~$16 price tag, it might be more cost effective going this route than buying a quality Micro SD card.

The screws provided don't fit the board; they are the correct size as they fit the brass standoffs, however the pressed in fittings in the board are tapped too small.I ended up ripping out the standoffs and threading screws through with a couple of small nylon nuts I had lying around to space it. Must say that it works very well, hopefully they will fix the screw problem. I think I have the fastest Raspberry Pi 5 imaginable.Can't use it so can't give it any better of a review.

First, if purchasing this adapter with a new NVMe SSD, I can recommend the Patriot P300 (https://a.co/d/8oPSNOz) as it definitely works with the Geekworm X1002 and the Pi5. I simply mounted the NVMe in a USB adapter, imaged Ubuntu 23.10 onto the drive, removed it, mounted it in the X1002, attached the flex cable and mounted the adapter under my Pi as pictured (with some stacking fiddling, as I had to use a combo of standoffs and screws to get it all together with my IceTower cooler bottom plate, but as pictured, it came together okay).The only issue I’ve encountered is on cold boot, sometimes the system doesn’t boot due to a timing issue with NVMe controller initialization, but a quick three-finger salute (ctrl-alt-delete) fixes the issue. Keep in mind, I’ve not adjusted anything with firmware parameters, and beyond that intermittent boot issue, it’s been completely stable. I’m also getting PCIe 3 x 1 performance.Running off NVMe natively is radically faster than any other Pi storage option and really puts the Pi 5 in a different class of performance versus previous models.