1950 2050 2150 Carburetor For Poulan Chainsaw Parts 1900 2055 2175 2350 2450 2550 262 Wild Thing Chainsaw Replaces 545081885 530069703 C1Q-W8 C1Q-W14 WT 89 891 WT-324

I have an old Craftsman chainsaw model 358.350802 and for whatever reason, of the seemingly 100's of different and similar model #'s, I cannot seem to find hardly anything for MY SPECIFIC model #. The saw had not been started in over a decade I'm sure. It was my deceased father in laws chainsaw and I really wanted to get it running. Through cross reference of similar model #'s and comparing the photos on the product pages with the equipment I have, I decided to take a chance on this kit, even though Craftsman and their models are not even mentioned in the product description. I got the kit and aside from the primer bulb, (which I knew was different) everything fit and worked great. I got the fuel lines put in and put in the new carburetor and fired it up and was cutting down trees in minutes. Really happy to find this product that was a perfect replacement for my old Craftsman when I could not find anything that was supposed to be an exact replacement. Very Pleased.

I got this carburetor to replace the original on my Poulan 2150 chainsaw. It was listed to fit my model and the carburetor fit just like the original. Everything you need that all in package. 25 years old Poulan starts w/ single pull I'm Happy!

I got this carburetor to replace the original on my Poulan 2375 chainsaw. It was listed to fit my model, but I found that it differs from mine, and in my case required a different part to fit. The kit has everything needed for a fuel system maintenance. It comes with a fuel filter, two sizes of fuel hose (small fuel feed, large fuel return), a new priming bulb, an air filter, a spark plug, and the carburetor with the gasket. Such a great price for everything included.I had some trouble feeding the fuel lines into the holes, but got it eventually. The addition of a fuel filter is nice as my saw never had one originally. The carburetor fit just like the original; however, when I went to assemble the air filter, the housing didn't fit this new one.My saw must be an earlier version of the model number, because this replacement has a different Choke Control Rod. While the new carburetor has a better choke setup, the air filter housing isn't the same. I had to get a replacement air filter housing that has a bigger relief cut out to allow for the larger new one. So check out your old carburetor when purchasing this upgraded one.Assembly was pretty easy after getting the hoses installed, and the saw started right up when I was done. I only had to make a small adjustment to the Lower Speed/Idle setting and I was good to go. I really like this upgraded carburetor kit and only wish I'd done it sooner.

Fast shipping..parts fit and worked as should

As soon asI put it on , my chainsaw started right up.Can’t beat the price for this carb kit.

My RamblingsBeen a while since I tuned up this chainsaw and it has begun to start hard and run rough.. So, let's just replace it all, because it's cheap to do so.To the Point or TL;DRTwo surprises: Primer Bulb Intake is on left side; however, Not in the way of throttle linkage. Throttle on both left and right side of carb, also, doesn't interfere with anything. It wasn't missing any pieces or parts. Chainsaw started after some priming and a four good pulls. Have your screwdriver ready to adjust. Adjusted it and runs smoothly. The carb didn't change my chainsaw it into a new one, but it made it run smoothly for the first time in a while... So worth $18.The Bad StuffNone so farWho May Use/Like ItThose needing a tune up on their very old, but still useful Poulan 2150.Me Final ThoughtsGo ahead and buy yourself a new chain while you're at it. My old saw running smoothly again. I could use a little of that myself.That's my story and I'm sticking to it. Hope it helps!All the best, Just BenjaminReviewed: Brand: Harbot Cost: $17.88 at time of review.1950 2050 2150 Carburetor For Poulan Chainsaw Parts 1900 2055 2175 2350 2450 2550 262 Wild Thing Chainsaw Replaces 545081885 530069703 C1Q-W8 C1Q-W14 WT 89 891 WT-324

I bought this to replace a carb on an old woodshark 1950 the carb will not fit but i did discover that all the internals, diaphragms gaskets, etc, are the same as the oem walbro carburetor. I disassembled the oem carb cleaned everything and replaced it with the internals from the new carb and wouldn't you know it works perfectly! If i was going to do it again i would try and find a gaskets set but overall pleased with the results.

In the listing it says it fits the Poulan Wood Shark 1975 but it is not even close. I would return it but it’s already been in the shop trying to make it work. The choke set up is wrong. It rubs against the plastic housing that holds the air filter. When installed you can pull the choke but it will not release do to hitting the cover. If you didn’t mind you could notch the plastic cover out and make the choke function properly. The other issue was the throttle linkage hits the nipple for the fuel line. You can tweak it to make work as we did but no adjustments on the High and Low settings could get the saw to run properly. On the other side of things the price was ok since it came with a new plug and fuel lines and fuel filter I can use on other projects. If your looking for a kit you can just toss on an go look at your style carb really good before getting this kit.@generationx1971 on YouTube