Printhead Cleaning Kit Printer Flush Kit for Epson ET-2850 ET-2800 ET-2803 ET-2760 ET-2720 ET-3850 ET-15000 ET-2750 ET-4800 2400 WF-7720 WF-7710 WF-7210 WF-7610 WF-3640 Printer Nozzle Cleaner

The media could not be loaded. I purchased this due to my printer setting for a long time and nozzles clogged. So I was hoping to find a product that could do the job and be cost effective. So I got the solution soaked my printer head in it overnight and the next morning my printer was unclogged. Came with the liquid and I like it came with gloves and a nozzle with the tubing already attached and ready to go . Instructions were easy to follow as well. Most cleaners you buy do not come with tubing so you can pull the ink out the printer .Overall product functionality was great unclogged the printer. Quality was good again it did the job and it was easy to use , and price was a lot cheaper than most.Pros-the product works for what it is intend to with ease.Cons-solution is red but you can see your inkOverall great product and will buy again.

My yellow print head on my Epson xp-440 was severely clogged (completely blank print). I tried every other less-invasive procedure I could find but nothing worked. Bought this fluid as a last resort thinking my printer might be toast, but it WORKED! The product came as described (100ml bottle, syringe, gloves, instructions). Felt a little small for the price, but considering it saved me from buying a new printer, it's worth it.It is very important that you follow the instructions and watch some videos for your specific modal of printer before giving it a try. Print heads are very complex and delicate, if you inject with too much force you can burst the print head tubes and permanently damage your printer. And if you drip fluid all over the inside of your printer you could cause a short circuit. You must be extra careful, clean and patient. This is not a 10 minute fix; expect to spend a good weekend on it.Important tips:1 - If you can, only remove the ink cartridge of the color you need to clean. If you need more space to access, remove all the cartridges, fit the syringe tube over the right color, then put the other ink cartridges back. It takes a long time to inject the fluid (at least it SHOULD if you’re doing it right), during which the other ink nozzles will start drying out if they’re exposed to the air for too long, causing more clogs. This happened to me but it’s not too hard to fix, just have to use some more fluid.2 - When injecting, use BABY pressure. Even slower than is shown in videos online (where they are usually using brand-new clog-free printers for show). It should almost look like the handle isn’t moving, THAT’s how slow. The nozzle tubes inside the print head are miniscule; if you think about the physics, even a tiny amount of pressure on the syringe handle becomes exponentially more pressure inside those tiny tubes. So have PATIENCE.3 - I layered a paper towel strip and two strips of watercolor paper (because it’s what I had) as my “blotting paper”. Worked well to catch the mess.4 - Warm up the fluid per instructions. Makes a big difference.-Finally, this is how I cleaned my print head:Filled the syringe with 4ml of warmed cleaning fluid. Then gently fit it over the yellow ink inlet (the one that was clogged). With BABY pressure, I injected a tiny amount of fluid, just enough to get it into the print head. Then I left it attached like that for about 3 hours total. I came back every half hour and gently worked the syringe handle (pushing and pulling), slowly injecting a little more fluid every time until the whole 4ml were used. I then replaced the blotting paper and repeated the process with about 3ml of fluid.Once finished, I cleaned up the inlet area with a que tip, replaced the ink cartridges and let my printer sit for another few hours before turning it back on and running a test print. It’s important to let your printer sit for some time after cleaning for a couple reasons (1) to let the remaining juice inside the print head do its thing, and (2) to give any possibly missed drips of fluid/ink inside your printer time to dry out before you start running electricity through the machine (precaution to avoid short circuits).After all this, I had to run a cleaning cycle only once for my yellow to show up perfectly! Very happy with my purchase!

Good product no instructions so bad to look it up but worded as said it would

It really works, I have bought different brands and this is by far the best nozzle cleaner. Will buy again just to have it at hand when needed.

I had one color (magenta) that had quit printing, and my black was working but I had to clean the nozzle pretty often. This was on an Epson ET-2760 printer. I decided to try this solution to see if it would fix the problem. After following the directions, exactly, I now have zero print at all. I did two nozzle cleanings and two power cleanings, after this stuff screwed up my printer entirely, and was never able to get it to print anything. The printer is now trash and I had to purchase a new one.

I used it followed the instructions and a few things:1. Booklet instructs to put cartridges into a plastic baggie to keep them from drying out. But it says this at the end of the booklet. Not the step where it needs to happen. Therefore by the end of the process my cartridges dried out and I had to do another cleaning of this printer when I’d already done so multiple times lessening the life of my printer even more.2. My pages printed absolutely blank afterwards. No matter what I did after the cleaning. And if any ink did come out, then it was more spotty than before. Now the instructions did say this could happen and there was a way to fix it but,3. I followed the instructions for if the page was blank inserting my ink because there was guidance on fixing the issue and some how the black ink seeped into my yellow cartridge and the fix also didn’t fix the blank problem and still is spotty. Maybe I did something wrong with the yellow ink issue but either way it didn’t work for the black.Maybe my clog was too far gone because I see that it worked for some but it didn’t for me. I wouldn’t recommend this for bad clogs and I’d be careful if you’re fixing the blank print issue.