240pcs 2inch Sanding Discs Pad Variety Kit for Drill Grinder Rotary Tools Attachment with 2Pcs 1/8"&1/4" Shank Backer Plate, Sanding Pads Includes 80-3000 Grit

I had a little project to do around the house and didn't feel like sanding by hand. I got a Dremel and these work pretty good. Granted, the attachment isn't perfectly balanced, so use the slower speed. However, the kit comes with tons of discs of different grits. Not only can you grind down your project, but you can polish it up nicely with the higher grits.

This is a good kit, lots of options and the quality wasn't a problem at all. For my application I found the ergonomics of sanding with a drill to be a literal and figurative pain.I ended up buying a corded orbital sander plus a comparable number of pads for $45 which made me regret getting this. The sander is more comfortable, faster, and I don't have to charge my drill batteries.Just throwing that out there for anyone with a project larger than a small side table, there are probably better options out there for you. That's not to fault this product, again it's a good kit and good value, which is why I'm leaving the 5 stars.

These did the trick where a bunch of other options had not. However, the 1/8” shank tool was inadequate to my dremel tool. A medium high spin was too much for the shaft and immediately caused it to bend. When I switched to a 1/4” rotary tool, it went great. The sanding disks don’t last very long but they send lots of them. Great tool for the price but just go for the 1/4”.

This was a great tool for fixing my leaky toilet flapper. I have a old style bronze flapper seat that had become a bit eroded in in a small section of the face that comes in contact with the silicone flapper seal, I'm getting too old to do a full replacement so I tried to hand sand or file the face but it's very tight quarters inside the tank and also you need to be careful to grind the bronze seat level and flat without gouging it unevenly. This 3 inch sander was the right diameter and comes with a 1/4 inch driver bit, I used a 12 inch drill shaft extension extension bit to reach to the bottom of the tank (I got the SeonFook 12 Inch Extension Bit Holder Magnetic Drill Bit Extension Bar Quick Release Change 1/4 Inch Hex Shank Extension Rod Socket Bit Holder for Power Drill ) which was ideal because the red tip that locks the bit into place spins like a bearing so you can hold that to steady the sanding pad while running the drill. This project was much easier than taking the entire toilet tank off and replacing the flapper valve unit and I saved money as well. Here's a link to the drill extensionhttps://www.amazon.com/dp/B09G6P154V?psc=1&ref=ppx_yo2ov_dt_b_product_detailsNOTE: this method is for Bronze/Brass flapper seats... it may work for plastic seats but you would have to be careful not to sand too aggressively and use only fine grain sandpaper disks. When sanding the bronze/brass seat I started with 180grit until I couldn't feel the corroded spot with my fingernail then used progressively finer grits ending up with 400grit to finish.UPDATE: I'm pleased to report that it's been over a year since I fixed the toilet flapper leak and it is still working great. This tool would save time and money for anyone who needs a quick durable fix for flapper leaks due to a corroded seat because sometime you don't want to pay a plumber or spend all day fixing it with new parts.

I love my chordless drills, and have purchased more attachments and adapters than is probably necessary, but I would rather have more of them, and less tools overall. This sander attachment, and all the sandpaper that comes with it, was the PERFECT thing for me. They work just as they should, and without a problem.

Hook & loop pads came off interface a few minutes into using. Sand paper comes apart bee quickly. Very low quality product but I knew they were cheap when I bought them so I can’t complain too much.

I would have paid the purchase price just for the 2-inch velcro sanding pad. So far I have used these tools for about 10 hours and I am extremely pleased.

I bought this looking for a quick and rough sanding alternative. If using hand drill, make sure to keep the pad moving or you will quickly sand through. I thought I was buying the 5" model, which helps for a more smoother sanding, I ordered the 3" instead and its much harder to control. 5" would be a lot easier. With that being said, it seems to function properly, but its just harder to control because of the smaller diameter. The larger the diameter, the better sanding job you'll have.

Ok de quoi faire 4 phares je pense

Rapport qualité prix au top. Utilisé pour refaire des phares de voiture, fonctionne très bien.

Does the job

Bought these disks in case I needed them to help restore my faded headlights. The restoration kit I purchased only had the 2000 and 3000 grit sand paper.I actually ended up using the 600, 800 and 1000 grit from this kit.The paper performed just as good as the one that came in the kit.I used the sand paper on a hand held sand paper attachment that came with the light restoration kit. Although I did try the drill attachment sanding block that came with the sand paper kit, I found it that for restoring the headlights by hand gave me more precise control. Which is important when working close to car paint.Great sanding disks, very happy with the purchase.

Bonjour, il manque un produit disque à poncer 180 ?