2130 1/2" Air Impact Wrench, 650 ft-lbs Max Torque, Heavy Duty, Pistol Grip

I have been performing maintenance on the family cars since my dad died when I was fifteen. That makes over a quarter century of brakes jobs and tire rotations, removing and tightening lugs with a T wrench. A couple weeks ago, I bought a compressor; mainly to keep the tires inflated, but I couldn't resist sizing it at least marginally enough to run an impact wrench. Then I couldn't resist going ahead and getting the wrench. I worked a little overtime, made my order, and my Ingersoll-Rand 2130 was on the table when I got home from work this evening. I immediately went out to perform an overdue rotation on the Silverado. Those who've used impact wrenches regularly will laugh, but I was downright dumbfounded when the wrench tapped the lug nut a few times and spun the nut off in a fraction of a second. And the wrench hardly attempts to turn in your hand. Had I known an impact wrench would make life this easy, I would have invested in the wrench and compressor years ago. I did some research before purchasing, reading a lot of reviews and comparing specs. I pretty much decided one was wasting his money going below about the $110 point. The other contender that would minimally meet my needs at the lowest price was the Ingersoll-Rand 231C 1/2-Inch Super Duty Air Impact Wrench . I'm sure I would have been happy with that, but moving up the 2130 seemed to be good value. For about $30 more you got a little more forward torque (500 ft-lbs. vs 350), a little more speed (9500 RPM vs 8000), about 2/3 the weight (~4 lbs. vs. 6) at very little additional air use (4.4 SCFM vs 4.2, however they measure that). I was a bit concerned about my compressor being up to the wrench. It's a Sears Craftsman 20 gallon, 1.5 HP, 150 max. PSI rated at 3.8 SCFM at 90 PSI (however THEY measure that). A lot of experts would say it's not enough. Sears said it was fine for 1/2" impact wrenches and only appropriate for intermittent use with a 3/4" wrench. I did some math and took the risk. For performing a tire rotation, the compressor was every bit up to the task. I really can't imagine any job in which the wrench would be used so continuously to really tax the compressor. If you're a shade tree mechanic, this compressor had no problem with the wrench. In fact, I had almost completed the rotation when I realized that I had turned off the compressor earlier when my three-year-old came outside and was terrified by the compressor. I had done the job with only stored air, it was still holding 90 PSI, and I had noticed no reduction in the performance of the wrench. I did not find any photos of the 2130 on the web that showed the rear the wrench. (I intend to post a photo or two in a the next few days) The red button in the side photo pushes left and right, choosing forward and backward. There is a five position toggle (at least on mine - the manual says it's three) in the rear to choose the maximum power. The switch is labelled from 1 at the lowest setting to 2 at the highest setting. Go figure. Power is also continuously variably controlled with the trigger, and I have to say that it is a fabulous trigger with fantastic control of speed. I've never used a power tool with fine control like that. I was also amazed at how quiet it was. It certainly makes little noise when it's not hammering, and when it is, I don't believe the 100 dBa plus listed in the specs (on the verge of pain.) I also ordered the Ingersoll Rand SK4M14 1/2-Inch Drive 14-Piece Metric Standard Impact Socket Set . This appears to be a great value as well. Time will tell how it holds up, but with my use, I expect it last a long time before requiring a rebuild. I can't speak for professional mechanics, but if you're a do-it-yourself mechanic, I don't believe you will go wrong with this wrench. Oh yeah...while you're waiting for your new toy to come, get a bottle of air tool oil. None is included.

I put this tool to good use right away to remove a 1 and 1/4 inch nut which was holding on the rear axle yoke on my 88 Chevy Pickup. I had tried to break it loose previously with a half inch breaker bar and couldn't budge it. I've never used an impact wrench before so I didn't know exactly what to expect, so I set my compressor at 85psi (manual says 90psi is max.) put the socket over the nut and pulled the trigger. About 5 seconds later the nut was off. I couldn't believe how easy it was. Putting the new yoke on was a bit tricky as you have to be careful not to damage the crush washer. I set the tool on the lowest setting and it was very easy to control with the trigger; I got it on with no problem. Next I needed to replace a brake caliper so I used it to pull off the front tire which was just plain fun. I'm just a shade tree mechanic but have found lots of uses for this tool. It's very useful and I couldn't have done some of the jobs I've done without it. I don't think you'll be disappointed if you decide to purchase it. I also purchased the Ingersoll Rand SK4H13L 1/2-Inch Drive 13-Piece SAE Deep Impact Socket Set to go with it as I was told that regular sockets would not hold up. These are great sockets, very hefty with easy to read markings (great for those with over 40 eyes).

Bought this when I started my job as a lube technician. It was between this pneumatic impact or a cordless electric impact but this won over it as it is much lighter (the electric impacts are just too heavy and tiring to be using above your head all day) It has been used daily for the last seven months and I’ve had no issues with it. All I do is add about four drops of tool oil every morning (definitely overkill but it’s cheap insurance.) I’d would highly recommend buying the boot that goes with this gun (Just search 2130 boot). The handle doesn’t get scratched up but the top part can if you aren’t careful when setting it down but with the boot, there’s no fear of that. I’ve recommended this impact to all of our new guys and it has definitely impressed some of the guys that have used other more expensive brands. Overall this is a really good impact for the price and great for someone just starting in the industry.

This is a well built impact wrench that I have been using on my car projects. It removes lug nuts from my 3/4 ton pick up without a sweat. It is heavy, but that is what you should expect from a "Heavy-Duty" tool. My only complaint is that impact sockets seem to be difficult to remove when changing sockets. Instead of the ball and spring that holds on the socket, there is a kind of heavy wire wrapped around the anvil that holds the socket on. Maybe with more use it will break-in and loosen up a bit, but right now it doesn't want to let go of a socket without a struggle. So far I'm happy with the wrench and it sure makes life easier when removing nuts from old vehicles.

I've been using this with a Craftsman Pro 26gal compressor. I did some research and this impact wrench had good specs for the SCFM rating I could support. Just changed my timing belt last weekend and it was great for removing the wheel, motor mount, crankshaft pulley bolt etc. The IR is short enough that it fits into most places you'd expect to use an impact wrench. Also, it fits well in my hands and has a solid feel. There are three power settings on the back. The counterclockwise rotation is full force regardless of the setting. With the middle setting, my lugnuts go on just a bit tighter than spec, so I actually avoid using a torque wrench when I use this.

Yes there are better impacts out there; however when I bought this one I bought it for home use on automobile tire rotations, this gun match my air compressors output and worked flawless, since then I started a new job in an industrial setting, I took this gun to my new job and was very impressed with the items it was able to remove, i mean i put the test to it. It didn't have enough oomph for Semi tractor trailer lugs, but for the lighter stuff it was perfect, light weight non fatiguing, and small enough to get into tight areas. Since then I have moved up to the 2135TI and am using this as a back up, and will eventually bring back home for the garage and auto use.

Powerful impact but u need a good compressor

works good, plenty of power