Metal Wall Mount Holder for Orbi Whole Home Tri-Band Mesh WiFi 6 System/Orbi Ultra(RBK850)(RBK852)(RBK853)/(RBS750)(RBS751)(RBK752)(RBK753)(960/860 Series)/(AX4200)(AX5700)(AX6000)(1-Pack)

I have the Orbi 970 Black (RBKE963B) and it fits perfectly.The bracket is thick and solid and mounts easily with three screws. The addition of thumbscrews for the router make it easy to attach and remove.The gap underneath allows you to easily feed the cables through and wind them around to maintain a neat look. I also like that the gap between the router and the wall still allows you to get behind there to add cables or pull out the power supply if needed. The official Netgear mount leaves no gap to work in and actually bends the power and ethernet cables, increasing the likelihood of breakage. This one has none of those issues.It’s a fantastic mount.

I bought this to mount an Orbi satellite in my workshop to go along with a new NETGEAR - Orbi AX3000 Tri-Band WiFi 6 Mesh System (3-Pack). I had already installed the RBR750 router at the modem, and the 2 included RBS350 satellites placed within my home, and had already ordered an additional NETGEAR - Orbi AX4200 Tri-Band Mesh Wi-Fi 6 Satellite to install in my workshop.However, when I inspected the bottoms of the RBS350 satellites, I noted that they are NOT constructed with the embedded nuts in the base. The router, on the other hand, does have the nuts. And the images of the Orbi AX4200 satellite on the store's website did not show the base of the satellite.I spent a lot of time making a plexiglass support stand to adapt to the wall mount for the satellite to be able to install in the workshop (before receiving the additional satellite). Had everything made to fit the wall mount before the new satellite was delivered.Upon receipt and opening the package, I did see that the new Orbi AX4200 Tri-Band Mesh Wi-Fi 6 Satellite had the nuts in the base! Everything did install easily. The satellite is quite steady attached to the mount. Unfortunately, I'd wasted a couple of hours making a holder that I didn't need (which is a good thing).Summarizing, if you are purchasing the Metal Wall Mount Holder for Orbi Whole Home Tri-Band Mesh WiFi 6 System/Orbi Ultra(RBK850)(RBK852)(RBK853)/(RBS750)(RBS751)(RBK752)(RBK753)/(AX4200)(AX5700)(AX6000)(1-Pack), you might want to check that your satellite does have the embedded nuts in the base BEFORE ordering this item.Please note that it does fit the RBR750 router, and it does fit the Orbi AX4200 Tri-Band Mesh Wi-Fi 6 Satellite, but DOES NOT fit the RBS350 satellites, unless you are prepared to make a bracket that fits on the mount to allow the satellite to sit in. If needing to do this, one can pick up a small sheet of thin plexiglass and cut out a piece that fits the base of the satellite, and taking into account making the sides, you can cut out small pieces on 2 corners (in the front), and using a metal straight edge, one can heat the area where you want to bend the plexiglass with a heat gun set to around 700 degrees F (don't heat too much to cause the plexiglass to bubble), and bend the edge up to a 90 degree angle - do this for the front and 2 sides.Overall, a great product, fits the satellite well (the one with the embedded nuts). Highly recommend!

The perfect bracket to hold an Orbi Router and or Orbi Satellite. Very secure and comes with all the hardware! Highly recommend this product.

You rarely find something that so perfectly fits its purpose, but this Orbi shelf is it. It's super easy to install. It's extremely sturdy (solid metal), it holds the Orbi in place (two perfectly aligned screws fit into the Orbi itself from below) and it's inexpensive. A very good product.

Installed in minutes. Love the minimalist design, no unnecessary parts or design.My only complaint is that the fit for the wires to the Orbi router can be a bit tight to get through if you're short on length of cable, so plan to place them accordingly.

This installed well and has a nice implementation for attachment and wiring and not getting in the way. The one negative to me is that the holes should be close together so that instead of having to use a drywall anchor, you can just drill 2 of the 3 holes directly into a stud. Anytime you have to hang something from a wall and they don't have them spaced close enough for a single stud install, or 18"s apart for more than one stud (If necessary) I don't like it. Over time I have seen drywall anchors slowly pull out.

Makes you install look very professional. I used raceway that can be painted. Looks fantastic

Does exactly as described. Clean look and effective method for wall mounting my Orbi AX6000.

Good quality mounts for ORBI RBR750 AX4200.I had an electrician install a outlet and RJ45 drop, near the top of the wall. The mount is metal, very stiff, wont bend easily and keeps the router off the wall about 2 inches. The holes for the mount lined up perfectly.Recommended for sure.

Great Quality

Wanted to mount orbi satellites and reduce the clutter.This works well and very happy with the quality.

I have this in the garage holding up my outdoor orbi and I do not have any problems with it at all. It's secure and well made.

Great product