WINSOON 8FT Single Track Bypass Barn Door Hardware Double Doors Kit, Heavy Duty Sliding One Track Antique Roller for Cabinet Closet Fit Double 53" Wide Doors

They looked beautiful when up, however be sure that you measure properly! Give yourself an extra 12 inches we under measured because we didn’t give it the extra 12 inches and they were too small, but they look beautiful up and they’re sturdy and solid.

This is my third set. Looks great, rolls quite, easy to install

stable, beautiful and resistant well made and smooth with the door would recommend these tracks

As other reviews stated, instructions were terrible and some of the measurements are inaccurate. (Ex: The holes for drilling into your door where the hanger attaches.) Now that I've done it, I would have no problem doing it again but getting started took half a day. We built our own door for our pantry and so far it seems to roll very smooth and we love the way it looks. However, we realized when we got to the 2nd door, that we were missing the other hangers. This is so frustrating. I called Amazon and they were very helpful but told me that there is no contact number so I would need to email the company. I did so immediately (it was Friday afternoon) and finally heard back from them Monday morning. It is now Thursday and after numerous emails, the one this morning stated that they were shipping my missing part and would provide tracking number. As long as I get what i paid for within a reasonable amount of time, I will be satisfied. I don't like that you have to deal with customer service through email alone. All of that being said, if you take your time and do your measurements correctly, you can figure it out. Just don't think this is going to be a 2 hour job and your done, unless you've installed several before. Also, if you are lucky, your studs will match up with your holes on the rail. We were not that lucky qnd had to use a header.UPDATE: I did receive all of my missing hardware and was finally able to get our other door up. We had about a 6 inch opening because we didn't account for the overlay between the inside and outside doors. We ended up removing the brackets and moving them over to make up for the gap. My final thoughts is that until you actually do the task, trying to explain or read about the process can be complicated. I would definitely use this hardware again, now that I know how it operates.

The track comes with everything you need and is easy to install. I broke a part (totally my fault) putting it together and when I emailed support I got an almost immediate response, they shipped two of the part to make sure I had what I needed, and followed up to make sure I’d received and successfully installed everything.

Everything was there and it was easy to install

The item is NOT NEW, it’s used and low quality. The instructions included were torn up so installation was hindered. They do not hang correctly and because they are also scratched up on the finish that shows I did not use and I would not recommend.

very heavy duty rollers, product exactly as described

Great value!! Saved more than half what retail hardware sites are charging for this item.Perfect for the space we needed it for a good quality !

Not an easy track to install. The good thing about the track is that it’s very customizable. The instructions were garbage. The hard part is figuring out how to get started. Once you do it once, you’ll know exactly how to install any track without the instructions. In the end the track was amazing. The bolts were to long for our door so we had to trim it. Again a lot of customizing. You need the right tools. Because of the way the doors overlap, our doors didn’t fill in the whole closet space but that’s a door issue not the tracks. Overall, nice track very sturdy and beautiful.

Very sturdy, made custom size doors due to space and lower ceilings

I used the hardware kit to install sliding by-pass barn doors on a closet entry area. The pre-drilled holes in the railing did not line up with the backing studs in the wall. So I disregarded the lag screws. Installed a maple header. Marked the header with the rail holes and drilled through (try to keep your drill bit level, you will need a 10 inch long 3/8 inch wide auger bit) and through bolted with 8 1/4 inch bolts. Be sure to shoot a horizontal line with a laser level where your rail is to be fastened, mark your holes before you drill so that your rail is installed as level as possible. Be accurate as possible during this procedure.

The hardware is well made and sturdy but 2 issues with the installation. 1) The hanger bolts, at 2 5/16", were 1/4" too long for my 1 3/8 doors. Cut them down with an angle grinder with cut-off blade, cleaned up the threads and continued with installation. 2) The outside door hangs about 1/4" lower than the inside door and contacts the floor. Cut 1/4 inch off the outside door and routed a new groove to accomodate the discrepancy. Overall not insurmountable issues however a bit disappointed with the extra time spent.