TG-3468

Looks great, easy setup, no heat issues as it sits right under my 3 fan GPU sucking the heat from it and my front fan bringing in cold air plus it has a great quality heatsink attached to it help disapate heat from it, solid internet speed and no issues so time will tell seams solid for gaming my fps are stable and no heat increase from my GPU TP link has great driver support as well.

TP-Link manufactures quality networking gear. Over recent years, I have relied on a TP-Link modem and I currently running TWO TP-Link routers, one as a 'root' router, the other as an 'extender/bridge' router. Always rock-solid and reliable. (I retired the TP-Link modem only because TP-Link does not manufacture a stand-alone DOCSIS 3.1 modem.) Note that there has been, over the years, four versions/itinerations of this (1 Gigabit PCI-Express) card. Sold and shipped by Amazon, I received Version 4.6 of the card. So Amazon is selling (direct) and shipping current stock. You can check the version of the card by looking at the label on the outside of the box … or at the sticker on the card. Oddly, the MAC address is not given on either the box or the card; if you need it, you will have to snag it out of your router's DHCP list. Installation into a WinXP SP3 w/ circa-2007 Intel mobo was quick and straightforward: All the drivers come in the box on a mini-CD but to be sure I would be current, I instead downloaded the most current Version 4 XP drivers from the TP-Link support webpage for the card. That was a .ZIP file; I extracted all the files into a temporary folder. Powered down the computer. Snapped the card into a vacant PCI-Express x 1 slot on the mobo. Powered back up and got the "Welcome to the Found New Hardware Wizard" pop-up. The XP driver install instructions provided by TP-Link (at their website) were very close, but not entirely 100% spot-on; if I recall correctly, from the pop-up I followed the path: InstallFromAListOrSpecificLocation Don'tSearchIWillChooseTheDriverToInstall HardwareType (choose NetworkAdapter) Don't bother to choose a specific adapter from the given list, instead click on HaveDisk, then Browse (to the .inf file in the temporary folder), then Open it. Click on OK. Ignore incorrect driver warnings and click ContinueAnyway. (I think the warning is being 'thrown' by the fact that the TP-Link card is built on a Realtek chip & drivers.) Bam! Device and drivers installed. Device is named 'TP-Link Gigabit PCI Express Adapter.' The three needed driver files were dropped into the Windows/System32 folder. Swapped the Ethernet cable onto the card. Opened ControlPanel/NetworkConnections. Disabled the mobo Ethernet port, renamed it 'Mobo Ethernet.' Enabled the TP-Link Ethernet port, renamed it 'TP-Link Ethernet.' Deleted the temporary folder. Rebooted the router, just to be sure. Up and running !! I didn't pick up the download speed improvement I was hoping for, but I've definitely excluded the Ethernet port as a speed constraint. (Paying for 1Gb, pulling 220Mb … time to get a techie out here to test the speed at the coax connector!) In any case, this card is very inexpensive … and it is also a quick, easy solution under XP and older mobos.

11/22/2025 System built 2013 (1st PC) Windows 10 (updated recently right before MS dropped all support) Mobo: Asus P8Z77-V Pro (updated iwht the latest BIOs) Onbard NIC: Intel 82579V Gigabit, Qualcomm Atheros AR9485 Wireless Optional NIC: Intel Giggabit CT (released around 2010), installed on bottom black PCIe 2.0 x16_3 slot Internet Speed Plan: 1Gbps Never used the onboard NICs, strictly ued the Intel Giggabit CT NIC for many years, was getting between 850-950Mbps, rrecently noticed it capping out at a little less than 400Mbps. Have a 2nd system, which is a clone of the first, it has the same Intel Giggabit CT NIC and is working fine, getting about 900Mbps. I took that NIC from the 2nd PC and installed it on the 1st PC, and got an average of 900Mbps, that proves that there is something wrong with the NIC on the 1st PC. I reinstalled the bad NIC on the 1st PC, did the same again, caps out at less than 400 Mbps, and got to the point where it intermittently does not even work at all. I started temporarily using the onboard NICs, both will intermittently lose connection after inactivity, system set do not go to sleep, only the monitor will, even tried turning off "Allow Windows to turn off device to save power", but to no avail, requiring a reboot to get either one working again temporarily, pretty sure it's a driver incompatibility issue with Windows 10, due to the outdated NICs. This issue will happen at least a couple of times per day. TP Link TG-3468 using RealTek chipset, I read some reviews of it dropping connection in Windows 10 and was worried that I may run into that also. Received it, the RealTek chip is RTL8168H, which is version 4.xx. Installed it and using Windows driver 9.1.410.2015, so far on the third day, no issues at all, getting between 850-950Mbps consistently, even after long inactivity. The Windows driver do not even show the Power Mangement tab in Device Manager, so it does not go to sleep (if Power Managerment tab is showing, best to uncheck the let it go to sleep to save power option". As long as Windows driver is working fine, no need to try TP Link's or RealTek's drivers. For $15, can't ask for more.

I'm going to have to say this is the best value in this product space. The Realtek chip used is really quite reliable, and I'm not easy to please. The Intel chip is better performance wise, but only by about 5% on the top end, however costs at least double, if not more. 95% of people won't be able to tell the difference in the performance even if they try pretty hard, and in the application this will be used, it won't be an issue anyway since maximum network traffic bursts will be in the 20MB/s range, at least for a few years. It's power consumption, about 1 watt at idle or very low traffic, is quite acceptable, and I'm also a stickler about that. An exceedingly simple card like this is hard to screw up, and they didn't, so that's a good sign. If you really need those 5,000 additional management features available on the Intel based card, go ahead and spend 4x what this one costs. Or is it 5x? I think I paid $10 for this one. Once, only once, did we try a card based on the Via chip. That card is in the trash now. Pay no attention to people saying it didn't work on their Windows box. If someone doesn't have the expertise to get the driver on to their Windows box, they shouldn't be adding cards to their box by themselves as it is. Any up-to-date version of Windows 7 or later has the driver already. And, of course, the card comes with a mini-cd with the driver on it, and it can be downloaded off the internet quite easily. If you're trying to add this card to a box that is 10 years old, well, bravo to you, but you will have to get creative unless you are running software that's newer than your box. We use Linux, and the driver has been in Linux distros for at least a year now. Even if the Linux release that you're running is a couple of years old, if you've been updating your kernel like you should be, you have the driver.

Easy installation of 10 minutes (you can find step-by-step instructions on YT for your brand/model of PC). Just make sure your PC has the matching type of expansion card slot for what you are buying (e.g. PCIe x1, 16, etc. AND that there is nothing ALREADY in that slot; check your computer's manual to find out; if you don't have the manual, download it from the company's support web site. I've included an image of a "typical" System Board [commonly called a "motherboard"]. Sys Board configurations vary and this is simply to give an EXAMPLE. Your board may be different, but it gives you an idea of what to look for regarding PCI-Express slots.). There should be no software installation required if you have Windows 10/11. Closed my PC, plugged all the cables back in, turned it on and after Windows detected it, it started "talking" to the other PC's in the house with a fast download/upload speed on the Internet. It's plain, simple with no bells-and-whistles and works great. WARNING!!! UNPLUG YOUR PC's electric power cable before attempting to open it and make sure you DISCHARGE ANY STATIC ELECTRICITY you might have in your body before touching anything in your computer or wear an anti-static wristband (about $6 on Amazon). WORD OF ADVICE: If it requires a lot of force to remove or install a component, 9 times out of 10, it either isn't supposed to be removed or doesn't belong where you're trying to put it.

10 gig performance, fairly instant plug and play functionality. Be sure to download the appropriate driver from TP link, then swap your network cable over. A low-profile bracket is included if you need it. worked flawlessly in my windows 11 PC. also, take note of the size of the PCIe slot needed, confirm you have a large enough slot on your motherboard - not being blocked by your GPU prior to ordering.

I bought TP-Link's 10gbe (TX401) card on sale after having Google Fiber 8gbit internet installed at my house. I also have a TP-Link AX16000 router, and multiple TP-Link switches. Until this card, I had nothing but great things to say about the value or 'bang for buck' of their products. Still no major issues with their brand, just steer clear of this card. My Win11 gaming machine kept randomly dropping connection under various load. Sometimes 1gbps, sometimes 6gbps. I didn't try it in my NAS so I can't comment. I had an extra Intel X540-T2 in my stash so I decided to put that in and give it a rip. Works flawlessly so I am returning this TP-Link 10gbe card. I tried various cables, drivers, settings, and all sorts of stuff to try to get it to work. Ultimately if it drops at random, it's useless. I was hoping to purchase a few more of these for our other machines in the house to remove my reliance on eBay 'Genuine' Intel cards. Other interesting behavior: it gets really, really hot. I suppose that's not surprising but I am concerned it doesn't have a fan on it to keep itself cool. I rigged up a 140mm fan near it and that seemed to cool it down quite a bit, but it didn't solve my issues. Aside from random drops, the performance copying files from my NAS was incredibly strange. My NAS also has an Intel X540-T2 and using my motherboard's built-in 2.5gbe (also Intel) NIC, I was able to get ~260-270MBps copying files over SMB. The TP-Link was all over the place: sometimes 10MBps, sometimes 200MBps. At random it seemed to do 800MBps with no real reason I could determine. This was between two Samsung 980 Pros on either end, so no caching/overhead shenanigans in theory. I'd be happy with this product if it was simply plug and play and didn't drop connection - even if it couldn't actually handle 10gbit sustained. I rarely see over 3-4gbit with Google Fiber (real world, not speed test) and my NAS drives top out at just under 900MBps anyway.

Works perfectly for upgrading an out of date motherboard that could only download at roughly 100MBps to up to a 1GBps. Simple plug and play, no need to download drivers.