VViViD Black Matte Car Wrap Vinyl Roll with Air Release 3MIL-VViViD8 (1.5FT X 5FT)

I used this VViViD matte black vinyl wrap to refresh the look of my car's interior trim and a few electronics around the house. The air release technology makes installation straightforward and forgiving, allowing me to reposition the wrap until I got the perfect alignment without bubbles or wrinkles. The adhesive is strong but not overly aggressive, so if you need to lift and reapply you can do so without leaving residue. The film has a nice thickness and quality feel that hides minor surface imperfections and provides lasting protection. The matte finish looks factory-fresh and professional, giving my project a sleek, understated look. After months of daily use, the wrap still looks flawless and hasn't peeled, faded or scratched. This product is great for DIY enthusiasts who want an affordable way to upgrade or protect surfaces on cars, laptops or furniture. Just clean the surface, take your time and use a heat gun or hairdryer for curved areas, and you'll end up with a result that looks like a pro did it.

Did a beautiful job of transforming the ugly metal surfaces in my kit to a professional appearance. Easy enough to use for my beginner self.

This wrap is one of the cheapest out there. Got enough for my jeep for less than $300. 3M 2080 would be double the price. Not the best for beginners because it’s thick, brittle, and pretty stiff material that requires a good amount of heat to work with. The adhesive isn’t the best, did a full post heat and post heated all the corners to seal, but some edges lifted after a couple of weeks. After the 2nd time post heating the edges that do stay but you practically have to melt the material to be sure it doesn’t move. All in all it’s the best price for decent quality just make sure you know what you’re doing. Finish does look great in the end but we’ll see how long it holds up compared to 3M 2080 and Avery sw900

I used this stuff to wrap the front of a portable AC unit. All of the furniture in my basement is black or with a wood grain pattern so the white AC was really out of place, it was practically glowing. I should preface this review by mentioning that I have never wrapped anything before. A while back I considered wrapping my laptop but with the way I'm so particular about very small details I always felt like the wrapping process would drive me crazy and I would never be happy with the end result. This AC project didn't require nearly as much precision as wrapping a laptop so I was willing to give it a try. The end result was pretty good. I ended up with a few creases toward the bottom around the left hand edge but it's virtually impossible to see that. I was mainly concerned with getting the front of the unit a smooth matte black. Mission accomplished. This wrap was fairly easy to work with. I was able to pull it off and re-apply it over and over as I worked my way down from top to bottom. I didn't have a squeegee or whatever other tools you're supposed to use, instead applying it by hand all the way down. I didn't use any heat at all either. On the bottom I had about a half inch of fold under so I used some electrical tape to secure the bottom edge. I'm not sure how well it will hold up but since it will be inside I think it ought to be fine. If it starts peeling off I'll have plenty more to try it all again. Final notes: - Dimensions: I dunno what dimension is supposed to be 2 feet, but this roll was absolutely not 2 feet in either dimension. I haven't completely unfurled it but I'm assuming that's the 5 foot dimension. The roll I received is 3 feet tall. So I'm pretty sure I received a 3'x5' product. This worked out ok but I was counting on the 2' roll as I would have only had to cut out my piece in one direction rather than trim it in two directions. - Packing: the outer packaging was a sturdy cardboard box with some paper which offered ample protection during shipping. However, there were two very annoying pieces of tape used to keep it from unfurling in its packaging. This tape left a slight oily sheen on the matte surface which I didn't realize until after I had cut the piece to size and applied it. I was able to "buff out" the oily sheen with a dry rag.

This wrap was sick! The color is near on point to normal matte black. It looked awesome on my bike!

I love this vinyl wrap. I use it on my motorcycle windshields. It is easy to use and looks great!

Perfect for what we wanted

Good product, i will install it on my car door pillars and trim. Fast delivery and value for the money.

Nice easygoing product

Excellent

Good quality