Syneticusa MB Retractable Hard Truck Bed Tonneau Cover Fits 2016-2025 Tacoma 5' (60") Box Powder Coated Matte Black Aluminum Waterproof Accessories

For the price you can not beat this cover. Instructions suck.Seller sent the wrong Cannister assembly in the first order and took them over a week to fix.They answer E-mails but do not seem to know much about the product.For 2019 Tacoma you will have to remove the TWO Tie down hooks in the front of the bed on the sides.Lay pieces out on floor, Support the Side rails with the foam from the package,Slide the Rolling portion of the top into the groove and Bring the rail just past the front of the cannister and screw togehter.Do the other side the same way.Lay complete assembly in the truck making sure that your front gasket is not bent under the cannister.Install Side rail hardware DO NOT TIGHTEN. Use the extra Piece of metal to hold the side rails apart at the back of the cover.And Adjust and center cover on bed check that the gaps are covered and tailgate close.Once you are satisfied with the alignment. Have Someone STAND ON THE RAIL and Finish Tightening down the Hardware to get a good seal.The Drain lines are WAY TO BIG. Go Buy some 1/2 To 3/8" Barb hose reducers and some 3/8 line.Cut two inches of the 1/2 Hose install barb and insert in the bottom of the cannister and tighten.Then install 12" of the 3/8" hose to the barb and run to holes in the bottom of your truck. You will have to make the holes bigger.BE CAREFULL THE Drain HOLE on the drivers side is RIGHT ABOVE THE GAS TANK FILLER TUBE> IF YOU DRILL TO DEEP You will damage this hose.Insert 3/8 Hose into the holes you made and your down.Pros: Lightweight, Easy to install, Looks good.Cons: Locks are Keyed differently on cover locks. (COME ON You cant get TWO Locks KEYED THE SAME?).Screws on top panel over canister are Silver not Black.Hardware for the side rails is not big enough to catch the complete rail. See pictures.Gets scratched very easy. The cover Got scratched from pulling a cardboard box off it. JUST THE BOX! NOStaples etc. Nothing in the box. The cardboard scratched it. So I do not Know how long this will last.I am Happy for know. Will update later. Does not seem to leak much more than any other cover I have had.

This roller cover is a great value. Seems to be well made. The install was a little tough getting it all lined up in the truck bed but not that bad. As another reviewer pointed out, the 4 screws that attach to the cover near the cab are silver and do not look very good since everything else is black. So I ordered some nice black aluminum license plate screw covers. I replaced the silver flat washers with the brass threaded washers that came with the covers. This way you can screw the black cover onto the washer for a secure fit. I used some thread sealer on both the security screws provided by the manufacturer and the caps. I think this made a great improvement in appearance and was really easy to do. I've attached before and after pictures so you can be the judge.

This thing was easy to install after I had figured out how to assemble it... 3 hours later. LOL. The instruction manual, 2 nuts, and drain hose are all missing. Heck, I do not even know if those items is supposed to come with it but crazy thing is, it does function correctly, and easier on my wallet. I would recommend this to anyone looking to save a lot of money, because this thing is straight to the point and it works. I hate it because it spent 3 hours trying to figure it out, but I love it because it was worth the effort. If you do decide to buy it and end up in the same situation as me, make sure you pay attention to all the stock photos on this listing and all the photos posted on the review section. It helped me figured out how to install it.UPDATE - I had purchased the wrong model to mount the rack mount on. But this model still has the t-slots to allow t-slot bolts to slide in. I was able to add the rack mount on top. Check out the photo. Best investment so far.

The roller function is really good and I've had the cover a few weeks now. The instructions and assembly took 4-5 hours because the curtain took some time (needed a second person to hold the side and the other aligns the curtain). The water outflow tube got tricky because the hold in the flatbed are really small however in the pictures attached, Home Depot had the right Brass fitting and the pipe adjusted right in. I had to cut some of the clear tube so it doesn't twist wrong. Really happy with this item!

this is advertised to fit a 2016-2025 Tacoma. There are major differences in the Tacoma after 2024 and this product does not fit or have the correct clips to work on a 2025 Tacoma. The return process is difficult and would not recommend.

This worked perfectly for my 2025 TacomaIt’s solid, no leaks and it looks sharp 😍Thank you