Huashan Replacement Brass Ceramic Disc Stem Cartridge Faucet Valve Quarter Turn 1/2" X 53mm x 12mm spline length 20 teeth(PAIR Hot & Cold)

I was getting tired of our very expensive kitchen faucet dripping about once every 15 to 30 seconds and tried sourcing a replacement valve at two local hardware stores. No luck. I looked up the brand/vendor for the Swiss made KWC faucet and found that the OEM valve a was available from one supplier in the US at the outlandish rip-off price of $66 per valve. I was almost prepared to buy it until I found that shipping was around an additional $75. Yikes! I took careful measurements of my existing valve and compared them with the very detailed drawings on this vendors page to make sure I got the right fit. I got two valves for less than 10% of the shipped price of a single OEM replacement. I only needed one. It arrived in Hawaii in a few days, installed easily in less than 3 minutes. Perfect fit and has a nice solid action feel. No more drips. 100% satisfied!

After shelling out more than $1,200 for a Whitehaus Collection Vintage III Bridge Faucet, Bar Sink Faucet and matching Pot Filler for our Kitchen Remodel in 2012, imagine my surprise to realize that the cartriges in these stunning, high-end faucets were absolute garbage.Once a year at least one cartridge would fail (leak) and need to be replaced. The only place to find these was directly from Whitehaus Collection and they sold them for $60 each! That one heck of an reocurring dividend for them on a $1,200 sale especially when you count the number of times I also had to replace o-rings and nylon washers to prevent leaks elsewhere on the body of the faucets! It was so common that something would fail that I'd buy a spare cartridge or o-ring each time I had to order a replacement from the manufacturer.Frustrated, I made it my quest to find the 3rd party supplier of these cartridges. I tried off and on for years but to no avail. Underterred, I started mapping out the threads, length, splines etc of the OEM cartridge and with every order of a $60 replacement cartridge, I'd search Amazon and other plumbing suppliers and ecommerce platforms to find a lower cost replacement.Finally, last week EUREKA... I got this PAIR of hot and cold all brass ceramic cartridges for $10 with free prime shipping and not only did they fit perfectly but they also work perfectly, no leaks, smooth operation and the water turns off when you turn the handle. Fingers crossed, they will last as long or longer than the ones from the OEM. They worked so well, that I came back and bought 4 more sets - 8 cartridges for less than the price of one from the manufacturer. Now I have in inventory to last me a few years with no fear that they might someday dissapear off of Amazon. Buy these if you have a Whitehaus Collection Vintage III bridge faucet!!! 10 out of 10!

OK, first let me say that I had two Aquasource (#289839) 8" spread lavatory faucets, so before I ordered these valves, to fix the old stuck cold side on the faucet at my property, I just swapped the entire cold valve assembly and handle from the extra faucet I had, and then I bought these valves to replace the just pulled cold assembly. I mention this because I do not have a need for my 2nd faucet right now and hence cannot say whether my new valve just purchased will be leak free. However, I was compelled to leave my review now because I put the new cold valve in the old faucet cold assembly I pulled and the fit was PERFECT. All the threads were in great shape, the handle fit perfectly on the 20 count threaded valve stem top, and the valve screwed into my old assembly beautifully. I put that all back in the box of my extra faucet box, so when needed, I have basically a brand new faucet ready to go, PLUS the extra HOT valve in the 2 set purchase that I did not need currently, all for $10, properly wrapped for protection and promptly shipped! I could not be happier to repair a quality old faucet like this with these quality replacement valves so economically! Note that I gave 4 stars in the "Instruction Quality" section, only because there were NO instructions, BUT NONE ARE NEEDED. Anyone who cannot clearly and easily see how these new valves go into the faucet's valve and handle assemblies has no business ordering nor using these, because it is such a basic fix.

Bought this to fix my Hansa faucet and it fits just fine.Sadly the Hansa manual doesn't give a part number for the replacement cartridge so I can't cross reference with that.Cheap enough that I'm buying another set to have ahead of time for when the next one starts leaking.

They are the same quality as the ones at Home Depot. But the circumference is too wide and I can't the screw ring over it to fasten it down. Threads and length are the same, but I must have an old system which is no longer in use. (1988).

Works as described, fits perfectly, easy to install, appears to be a better seal than the original.

they are almost the same size, the difference is minor and they are working just fine in place of failed Grohe 45882000 and 45883000. I bought couple of more for a backup

I didn't want to pay $35+ for the OEM valve cartridge for a sink that started peaking from the handle (a Jado sink, formerly an American Standard brand label). This cartridge set appeared to match the dimensions, but didn't expressly say it was a replacement for the part I was looking for (H960136.191). I am happy to report it is working just fine, in case you are also looking for a similar replacement.