PC Products PC-Clear Epoxy Adhesive Liquid, 1oz Double Syringe, Clear 70147

Bought this to adhere my security doorbell to sheer glass, and so far it's held beautifully. In fact, I had to move the doorbell after it had already been set in place. Used rubbing alcohol and gently pried it off. Seems like it would take alot to un-stick the doorbell under normal circumstances. Just wanted to mention that it sticks well, but It's not the end of the world if you need to move something you epoxy-ed. It's easy to work with, but bear in mind that once the epoxy and hardener are mixed, you don't have alot of time to work with it before it hardens. The four minutes advertised on the package is about right. I used a bamboo skewer stick to mix it, and used a piece of cardboard as a "palette" , that way I could just discard them after use. Another good idea is to set the item being glued, and then secure in place with duct tape to let the epoxy cure. But if you had to, you could pretty much hold it in place with your hand, it sticks and cures pretty quickly. I liked it so much, and it was so inexpensive, I decided to buy 3 more. I have epoxyed metal signs to a very rough-surfaced brick wall, because it's hard to screw or nail them in. Stuck perfectly, and seems to be on there pretty solidly. I will update this review at a later time to let you know how well it stuck over time, but so far it has exceeded my expectations. So overall it works, it's pretty easy to work with, and it's a great value considering the very low price. I highly recommend this!

The product works well. No surprises. . The stopper or lid/cap that holds the liquid mixtures in is well designed and comes on and off easily. You don’t have to cut the tips and deal with annoying snap-on caps/lids. The lid/cap simply twists on and off. I’ve used the product four times already removing and putting back the lid/cap. No mess and the cap/lid works and comes on and off without issues. . The plunger is smooth and trouble free. . The two liquids come out clear and transparent, but turn slightly opaque when mixed. The epoxy mixes into a liquid consistency similar to chocolate syrup rather than tomato catsup, so viscosity is not that thick, so it will run. I recommend using a tray to mix. I used a piece of cardboard and experienced some running. . When applying, note that the epoxy is lesser in terms of viscosity. It will run off your scraper and spill, so take care. But spillage is easy to clean with a wet paper towel. . Don’t over-apply. Just make sure you can get even costing on both aurfaces/sides of the materials to be bonded. . No nasty odors. . A couple of minutes after application, the epoxy feels sticky and rubbery, but that goes away and the material will turn rock hard after an hour or so. Epoxy dries clear. Hardly noticeable even after applied on a wooden door that is painted white. . Very good bonding. I used masking tape to clamp/hold the glued pieces together. And the tape came off easily after curing/hardening. . I would most definitely buy this product again.

I used this for gluing a broken piece of ceramic together and also for kintsugi, mixing it with mica for color. It worked great as an epoxy, and for the kintsugi, filled a hole and dried hard as metal. So that function it great. I did however downgrade the “ easy to use” rating, because it didn’t dispense evenly. When I first pushed the plunger, it came out of one side before it did the other, as if there was an air bubble in one side. The amount evened out as I continued to push, and I dispensed more than I needed, to decrease the difference. It did dry hard, as a stated above, so maybe the 2 parts don’t have to be exactly the same amounts, but I did think it was worth mentioning. There was one feature that was very useful. The cap that you put Back on to store it only goes on one way, so you don’t have to remember how you took it off. There is no danger of left over harder in the cap mixing with left over resin in the plunger and glueing the whole thing shut.

If used properly, this stuff makes an incredibly strong bond. I used it to attach a copper pipe to an aluminum pipe on a DIY project. I realized that I needed to make changes and get the copper pipe off. Nope I broke the copper before I could get it to budge, Which I then had to hack saw it up and break parts off with pliers to get the copper off so I can re do it. As an adhesive, thats pretty much a 10/10. My intent was ot make my 2 pipes one, and this did that pretty perfectly. If you use this wrong the bond wont be great, but used well its amazing. Bonding 2 flat surfaces together isnt nearly as good. If you rough the surfaces up it helps, but all it needs is for one edge to cope up a tiny bit and it can be popped off. But if its a 3 dimensional joint, so that theres adhesive stopping it from moving being able to pull off, its amazing. When properly used, everything I try to take off breaks before the epoxy goes. So as a permanent solution I couldn't ask for more. And for ease of use, its very easy to use. I just squeeze a bit onto a piece of cardboard with packing tape on it to make a water resistant surface. Mix them with a paper clip. Apply it. Wait. Note that a hot environment will set faster. Try not to get it on your hands, its sticky and doesnt come off well, even with dish soap. But its not like super glue so it wont just instantly stick your skin together. so it gets points over glue for that. Also this is incredibly cheap and non toxic when cured. Meaning it should be safe for most applications. I cant really ask for more.

Very easy to mix, dries crystal clear, holds on tight. A must have for clear bonding.

This epoxy works as expected. It's quite a bit, so if you don't need much, maybe go with a smaller amount. It's very smelly after opening and a Ziploc doesn't contain the smell. Keep it in your garage or outside of your house.

The. epoxy works great, other than the smell I would rate it a 10/10. It cures fast and holds like iron.

Bought this in Jan 2021. Product was great to use but about after 7 months of ownership I noticed that the hardener was turning a yellowish color and eventually turned into the consistency of a hard paste that I could not get out of the tube easily. Had to separate the two plungers so that I could press the two sides with different pressure and continue to get some use out of the product. Since epoxy and hardener should last about 3 years, I am wondering how old these items are coming from the vendor's warehouse. This is the second time I buy this product. The last time I purchased two of these and was unable to use the second one because all the material (epoxy and hardener) had solidified in the tubes. Please note that these products were kept indoors at room temperature and well sealed with the cap provided.

Excelente epóxico, de verdad que sí pega el cristal, ya lo utilice en el cristal de mi comedor y de verdad que sí resiste..

Sent without packet - only the syringes were delivered wrapped in a plain plastic wrapper. No instructions for use were received.

اشتريت باقي التجربة ان شاء الله ممتاز

Muy buena aunque es muy poco precisa. Huele muy mal pero supongo que es por la resina.

This stuff is great! I bought it purposely to repair the lid of an old ceramic sugar bowl, of purely sentimental value. I already had superglue, which would probably have worked but does not give a very strong bond. I have used epoxy adhesives in the past for ceramic repair and often been disappointed by the poor fit of fragments and the yellowish lines of the adhesive that remains clearly visible between them. The simple dual-syringe mechanism works perfectly, as does the re-sealable cap. Working time is sufficient to mix the product, apply with due care to two surfaces and to press the pieces into position until they are fairly firmly fixed. It's worth noting that you also have a short time to wipe away any excess adhesive - definitely do this before it sets! I left the repair to cure fully overnight and the result is perfect - the join is almost entirely invisible.