106" 16:9 HD Electric Motorized Projector Screen + Remote

Coming from a fixed frame screen at 166" in my previous dedicated theater (that's 14 feet by the way), my concerns over being satisfied with a non-fixed screen at a smaller size were high; especially considering the low price. That being said, my experience has been fantastic! The purchase was from shop247 who is listed on the manual as the company for the screen, so that's a plus. That's about all there is to the manual as it is basically just a folded single sheet. The box arrived in excellent shape, covered in shrink plastic. There was no damage, no dents/dings/whatnot.I hung the screen on the front of my entertainment center from some custom brackets that basically provided a place to put 2 screws so I could hang it as if it were mounted on the wall. This was trivially easy as the screen only weighs about 20 lbs. Once I finally rolled it down I was relieved to see it was all going to be okay! Yeah, I could smell the vinyl initially but that went away very quickly. I see people complain about quality, but I am in the complete opposite camp. I am astounded that this can even be produced for the cost. I think it is very high quality, works perfectly and I was able to get a flat picture not unlike using the fixed frame screen.Now there was a slight wave/ripple coming from the upper right corner. I think these are inevitable and will vary depending on the shipping conditions alone, but the cure was some gentle manipulation. This is so subtle that close to the screen I could not perceive the ripple from the white side. But the trick was to look at the back of the screen as it is way easier to see the ripple on the black side. I put 2 lb weights on the corners of the screen to help stretch it out. I actually used a couple of industrial staplers as weights as they were convenient and the handles would just hang from the bottom bar. Then I used a tall space heater on my side speaker behind the screen to warm it up - just enough to relax the fabric; maybe 30 seconds to a minute hitting the back of the screen at a diagonal so it blows across the back and uniformly warms it. Then I removed the heat and gently pulled the edge just enough to hold the screen flat. Hold it there for several seconds until it completely cools and voila... it holds the new flat shape. That is my inside take on putting it in the sun solution; basically a very wide hair dryer.The aspect is a perfect 16:9 so I was able to get a pixel to corner perfect adjustment on the projector. The picture is satisfying and I have consumed around 100 hours on it already. I am set up for 120Hz 3D (nVidia) and that also works perfectly. So ignore the haters and give it a go. I would definitely buy this again and my neighbor is already planning to pick one up for his basement after seeing mine in action.Satisfied? Absolutely!NOTE: I purchased the 120" screen and the very next day after posting the review the 120" became unavailable on Amazon and even my order link directs me to the 110" version and seems to indicate that was my purchase. Odd....

I bought this screen not really having *any* experience with projector screens but have a projector and wanted to get it setup for gaming and movie night. The prices seemed to be all over the map but I knew I wanted a motorized, decent size screen. I ordered this based on the positive reviews, price and free shipping. The screen arrived really fast and was super easy to mount and came pre-assembled. I like the fact it has a manual control (wired) and wireless controller to extend and retract the screen. I mounted mine about 10' high so the power plug isn't long enough to reach to a standard wall jack and requires I use an extension cord. I may have power installed somewhere to accommodate the power plug but need to think about where best to have that done. The strange thing is the manual control runs on the same cord as the power and both exit the control box on the top so it's kind of a weird setup and doesn't present a streamlined cable run. When the power is on, the manual control box has a red light; which irritates my wife when watching a movie so will have to mount it so the light isn't detracting from the movie experience. (I told her to pretend we're in a theater and it's an illuminated exit sign in the distance...)The screen itself is rather thin and not heavy duty as I've seen with screens in the office. Despite that, the picture shows great on the screen so it definitely does work well. Others have also mentioned the thin construction of the metal housing as well but agree it reduces weight and isn't something that needs to be super thick based on the application. I did like the fact it comes with mounting in the back to direct mount into the wall or alternatively hangers to hang from the ceiling. Unfortunately I couldn't mount to the wall or ceiling to used L brackets to get it about 8" from the wall and then hang with the hangers. Worked perfected and is generally flexible with respect to mounting options which I found to be a plus.Ultimately I'd give the unit a 4.5 in terms of stars but decided to just give it a 5 star since the minor dislikes I mentioned above are just that - minor. Keep in mind I'm a newb when it comes to projector screens so I by no means an expert but found this seems like a great deal and is amazing to have a huge picture on the wall that all folds up nicely out-of-sight when finished.