3M Panel Bonding Adhesive 08115, OEM Recommended Two-Part Epoxy, 200 mL Cartridge, Bonds Metal & Composites for Auto Body Panel Repair (1 Cartridge)

Wow!!! This stuff is fantastic. Grips like no other. Goes on easily and cleans up just as easily. It hardens quickly yet has a long enough window that you can work with it after applying. It's not cheap, but if you're doing auto body work, YOU NEED THIS.

This stuff is superb! High grip adhesive. Holds where it is placed so make sure to put it EXACTLY where you need it since you’re not going to get it off again! Adheres to literally everything I’ve tried it on.

Have used this material on multiple custom car projects and it works extremely well. You can also use it to fill small holes and make surface repairs as it can be sanded when cured. MFG recommends a high grade primer before top coating. This 08115 is the faster setting compound (90 minutes work time) and has worked in our shop when its colder outside, just like an accelerator (low temp accelerator) in auto painting. It has successfully cured clear down to 40 degrees, then the part was put out in the sun for final cure. Can be re-used at the partial tube amount if you are careful putting the cap back in and not mixing the compounds from cap contamination. MFG says the shelf life is up to a year, make sure to check the product you receive as there is a date stamp on the tube showing when it was manufactured and in some cases when it expires in case you get a batch of old new stock. Strongly consider using this in place of welding where appropriate. Best to use bare metal to metal, scuffed up or with grind / sand marks to give it best chance of adhesion. The gun applicator is expensive as is the material, however the expense quickly fades when you realize how useful it can be.

GOOD PRODUCT LESS EXPENSIVE THAN PAINT SUPPLY STORE

It provides a strong and reliable bond for my automotive repairs. The two-part epoxy is easy to mix, and it sets quickly, allowing me to finish my projects without delays.

I used 3M 08115 for the first time on my 1954 Chevy Pickup that needed some small patches on its holey roof and firewall. I chose this product after many hours of research and debating vs welding, braising, fiberglass, and other products. the le reason why I chose this is because welding large surfaces such as a roof can warp the roof if not done properly and even then there is no guarantee. Another reason is that welding melts both metals down and can potentially inbed impurities and rust into the weld only to pop up later. With this epoxy you eliminate the potentially for any of this to occur. This is probably some of the reasons why most car manufacturers are using this product to secure their panels on their cars in lieu of welding. Also, because it seam seals all in one step. From all the forums posts and reviews that I read I was unable to find anyone that had actually used this product that wasn't completely satisfied with it's performance. I borrowed a really nice gun (it requires a double tube epoxy gun btw) from a friend and went to town. It applies like hot peanut butter, gives you plenty of working time, smooths out flat, and it cures hard as steel. I love it. I have since used it on other projects and it has performed great. Some tips: It says on the product material that you can reuse it by leaving the tip on there, let it dry and leaving it on till you need it again at which time you just unscrew it and put a new one on. I read this after I have cleaned the outlet very well and put the top back on. This can be a little tedious. Using the used tip seems a lot easier to do. Another tip is that I was working with small 2"x 2" patches for my non structural hole repair. I found that using small yet strong magnets to keep the patches in place as they dried worked awesomely. For the intended application, it is the best there is. Try it and you'll agree. Update....... I have used this product a lot since this posting and continue to be in awe of its strength and ease of use. I can see most welding falling into antiquity when everyone finally brakes from what they are used to and tries this stuff. BTW for shorter claiming times, apply heat from a heat gun. It sets up in about three minutes. Another benefit to this product is that you can bond unlike metals such as steel and aluminum and since there is a layer of epoxy in between them you don't have to worry about them reacting with each other causing galvanic corrosion. sorry for the long-winded review but I hope you find this helpful.

Man my buddy has a body shop and put up on this. This stuff works will glue something together and it’s not coming apart! When I say it’s together it’s together and it’s not coming back apart. Not for the weak

Very expensive product wish it had more quantity but it works good

Good stuff

Très bon produit et efficace

ポルシェの、カーボンルーフ加工に使用。20分程度で硬化し始めます。その間に接着物の両方にヘラで塗布均一化を行い。接着します。特にFRPやカーボンは、塗布後 硬化が早いので、早く接着が必要。最初は、ゴムの様ですが、硬化後は、カチカチになります。

スチール、アルミ、ファイバーが接着出来てとても素晴らしい接着剤です。 基本的な下処理をきちっとする事が大切です。 価格が高い高いのが難点です。 自分が思っているよりたくさんの量が必要な時が多々あります。

Product was used to bond fiberglass hood bulges to my original metal hood, also used to bond a carbonfiber trunk lip to my original metal trunk lid. I scuffed you the paint a bit to give it something extra to bite into. There was about a 45 minute work time with it before it started to “set”. I had it clamped over night, but 3m claims only 4 hours is required. I would believe them, I just took extra caution. Product works super well, will be using it again shortly. Highly recommended.