eMylo® AC 220V-230V-240V 1000W 6x 1 Channel Smart RF Relay Wireless Remote Control Switch Transmitter with Receiver

Great piece of kit. Easy to install once you figure out the wiring. The diagram is t too clear. For anyone not sure, 1 is both neutrals (Blue) 2 is live incoming (red) 3 is live switched (yellow) and 2 & 4 should be looped to each other. You will also need if using outdoors a clear lid IP66 housing large enough to take all of your wiring. If using a solid plastic lid, I found it weakens the RF signal. They work great on all my outside lights which I have rigged up on 4 separate circuits. Going to buy more for friends Christmas gifts. Any questions please ask.

For the money worked great for the project I needed them for, instructions are a little confusing and the live and neutral are different on the pcb to the instructions so check before putting any power. Worked fine on UK Mains power (these are the mains ones not dc powered). Found that I had to get closer than I would have liked to use the remote but was OK for the job I needed them for

Very neat, which makes it slightly fiddly to wire in, and programming the remotes is a bit fiddly, but OK. When installed, works perfectly, and I switch on a 50w led light to light up access to my driveway from inside the car at a range of 15 - 20 m. Perfect for my requirements.

Very good value.The way the unit behaves on remote button press can easily be changed via a pres-button on the board.I found the range a bit limited initially, it wouldn't trigger when the fob was indoors and the receiver in the garage, a separate building. I found that uncoiling the antenna wire and leaving it dangling increased the range significantly and it then worked reliably.The relay contacts are 'volt free' so you can connect them anywhere you'd have a switch. You could use it to power house lights if you wire it such that the COM and NO contacts replace the switch, and L and N supply mains power to the receiver. Simple enough to do, but of course if you're not confident get somebody who knows their stuff to do it, mains can kill!I did find that the housing it's supplied in is a bit curious, it prevents access to the relay terminals. Bizarre... I had to cut a slot in one end so I could get the wires in.Bear in mind that the device needs to be installed within another box since the connector strip allows contact with live mains.Overall, highly recommended.

Seems to be working as intended, but not being proficient with electronics I had a tough time figuring how to connect this thing, even though the manual was provided.So here's the deal: IN+ and IN- are for powering the device. You plug the hot wire into one and the neutral wire into the other. Doesn't matter which to which, as long as they are not the same wires. Then you need to connect either neutral or hot to the COM (Common) pin. I recommend the hot wire if you're sure what you're doing - otherwise try with neutral. Then if the relay is off it will transfer the current from COM to NC (Normally Closed), but if you switch the relay using remote it will transfer the current to NO (Normally Open). If the hotwire is connected to COM, the connect NO to the hot wire of whatever you'll trying to power, and the neutral wire from your power source to the neutral wire of whatever you'll trying to power.You can bridge the IN+ with COM using a wire.

Works really well. I control from the house to the garden shed which is some 10 meters away. The remote is a pleasure to use. The information provided about wiring the remote is confusing. You need to take the top off the controller, then look at the connections which are labelled. The 2 on the right are for power (as per the information), then the next 3 are the relay .Overall, really impressed.

What can I say, a superb piece of kit. Programmed in less than three minutes, installed in 10 minutes. Yes it does need a dedicated neutral feed but that didn't cause me an issue as i always run 3 core to all switches (as a just in case ) I would have given five stars but there seems to be a coding anomaly when in mode 3 . I set up two units - unit 1 (jog - to activate a door opener) - on - remote A ( Push - release ) - unit 2 ( toggle - hall lights ) - on remote c -off - remote d - this worked ok, however - when 2 was on and and 1 was triggered - 2 went off ??.I tried all combinations of button configuration but couldn't get this to work correctly.This was finally overcome by switching unit 2 to latched mode, which was a bit of a pain , as i really wanted a dedicated "off" button.I'm running a Broadlink system and all 4 devices programmed seamlessly into this , so effectively I've got 4 remote / wifi/ 4g integrated switches for the price of 1 Wallpad Rf light switch ( I now have a spare remote too )I bought these Thursday - delivered Friday ( Thank you Prime ) - and I'm ordering another 4 Monday ( Let's hope they're not on the same channels )

Worked fine for 12 months. Today however, spotted that the light had come on in the shed. Strange as I hadn't turned it on. Went to the shed to investigate. Terrible acrid smell. The box had started to melt and was extremely hot. Looks like it killed itself, competing the light circuit in the process. Pretty sure that it would have caused a fire if I hadn't spotted the light being on.I wouldn't buy this again.

Sencillo y útil, tenía un receptor que no podía acoplar mando y me ha servido genial y económico

Top Qulität

Im Gartenhaus haben wir einen Umbau gemacht, wobei wir auch mehr Licht als vorher brauchten. dabei lag hinter der Vertäfelung bereits Strom, aber kein geschaltetes Licht. Diese vier Relaisschalter schaffen nun ein wunderschönes Ambiente, was man mit Hilfe der Fernbedienung auch wunderbar schalten kann. Die ideale Lösung unserer Thematik! Installation mit Hilfe der Anleitung für einen technisch versierten Heimwerker einfach, Funktion 100%. Ich bin absolut begeistert

Das ist eine Top Produkt ich kann nur empfählen

Die Fernbedienung hat eine gute Reichweite, der Anschluss ist problemlos. Lediglich das programmieren mehrerer Sender auf einen Empfänger kam in der Anleitung nicht vor (einfach nach dem ersten mit dem zweiten weiter machen). Der Empfänger funktioniert auch mit dem im Rückspiegel integrierten Sender meines 15 Jahre alten Mercedes (Signal vom Handsender kann vom Autosender aufgenommen und wieder selbstständig abgegeben werden).