YONICO12335 Ogee 3 Bit Raised Panel Cabinet Door Router Bit Set 1/2-Inch Shank

Seen ok only used one of the bits

good piece of kit, i have done a good diy project doing my shutters

nice bit! thank you!

not bad for money save up next time for better quality set.

Purchased this set to mill maple rails and styles for cupboard doors and draws I was building. I was a little leery of the quarter inch shanks, but the bits performed flawlessly in my ancient one horsepower Craftsman router table set up. Had to adjust the positions of the cutting heads with the shim washers provided to get a tight joint. Other than that no difficulties.

Me gustó el empaque como llegó la calidad de la información de la caja y las fresas se ven de excelente calidad en sus materiales bastante robusta en unos días las probaré

Alles in Ortung.

OK so first off I am not a professional woodworker and just do it for hobby.I will say this these things are great and I have had no issues with these and to be honest with any of the Yonico Bits I have purchased through Precision Bits.So I have used these on a few types of wood that to be honest is a bit uncommon; but I am working on a special project.I will just say this I have used it on Blood-wood and Purple-heart both are very hard woods. So did the bits hold up yes they did.On my first go at it with Purple Heart I had minimal burning (but to point out that was my fault along with Purple Heart is pretty easy to burn) On my second go at it once i adjusted the feed rate and speed on the router i had just a little burning (tiny pause is my feed rate); but once again my fault I don't blame the bits for it.The fit and cuts came out pretty much flawless (other than my first go at it; which as i said was my fault for going to slow and pausing a bit in a few spots if i remember correctly but i don't remember the reason i did) That said I will also say that the joints fit perfect and there was no splintering.I have attached a picture of what it did to purple heart and blood wood. This still has the burn marks on it; but once again mind you that was my fault as you can see on the other side there is only one spot where i slowed the feed to much. (It was my first time with routing Purple Heart). (Yes its also a rough out and have to cut some stock etc.)I have also used it on pine and red oak and results have been great.So I cannot attest to how long they will last and hold and edge but I mean come on I ran it through some of the hardest woods and got great results (other than the user error part). If they are like some of my other Yonico Bits I believe they will last for as long as I need them too. Some of the bits I have used by Yonico are on point with other major brands. I really believe they will beat the normal store brand bits hands down. As a whole are they as good as Freud bits... I cannot fully answer that question given I only have a few Freud bits. I will say this though of the bits i have that are the same from Yonico and Freud... I honestly don't see a difference in the cuts they make.I would highly recommend these for a hobbyist woodworker and at the same time I would even recommend it to a pro and I say that because of the price point. As a pro you really don't have much to lose giving these a shot to see how they compair and if you find them up to snuff well you found a bit / brand of bits that is 1/4 the cost.I honestly have faith in Precision Bits and their quality and would not merely avoid them because of the price point. They get the job done... Period.One last note NO I AM NOT EMPLOYED BY OR RECEIVE ANY COMPENSATION OR ANYTHING LIKE THAT FROM PRECISION BITS. I have just had no issue with Yonico (which are their bits) and have read on some woodworking sites to avoid them by people who have never used them SIMPLY based on the price of them. If you ask me that is bad advice. Just because you spent 200-300 on a set that does the same thing does not mean everyone else has to... and if you have never used them how can you say they are not good... simply based off you spent 200+ on yours and these are $50ish... BLUF these get the job done and that is what we are all looking for right?

Me llego antes de lo previsto, las brocas trabajan muy bien al menos para mi q soy aficionado,están excelentes!!