INJORA 313/324mm Wheelbase Chassis Kit LCG Carbon Fiber Frame Girder for 1/10 RC Crawler TRX4 Upgrade Parts

This kit rocks!!! The trx4 is a good crawler out of the box, but this kit turns it into beast mode. Everything is top quality and the carbon fiber is also good quality. The assembly is straight forward for a hobbyist. The trx4 stock is good for bashing though, so if you want to bash then this kit is not for you. If you want to climb Everest then this is the kit!

Excelente chasis

The only redeeming quality this kit has is that it is cheap. If you value your time, look elsewhere.My expectations were low going into this, but INJORA went lower.-Missing M3 nuts-Front end will bind hard with the included rod ends. Need to use the angled ones from the stock truck on the upper link. And even then it will require playing with link lengths to tune out all of the binding.-Rear end will bind hard with the included rod ends. Need to use the angled ones from the stock truck on the 2 upper links.-Rear link lengths are way off. Had to mix and match the 324 and 313 links to get a functional pinion angle.-Drive shafts work ok if you swap them front and back. Not the best, but it's passable.-The pinion is half hanging off the motor shaft in order to line up with the spur.-They could have pushed the transmission forward and fixed the above 2 issues. There is plenty of room for it. At most this would require an extra hole in the motor plate for clearance on the spur gear nut.-Doesn't come with a servo mount, stock servo mount doesn't work either. So you either need to make your own or spend more money and buy one from them.-Rod ends are super low quality. Some of the hollow balls are too tight and some are too loose.-Hardware isn't organized well at all. Sometimes the screws you need are in the same bag as the part, and sometimes they are in a separate bag with a completely unrelated part.-ZERO INSTRUCTIONS. Not even an attempt was made to send you on the right path of putting this thing together. Even just an exploded view with the bolt lengths would have been a huge time saver.

I bought this for a budget build for my Trx 4 1/10 scale truck. I transfered all my parts over to this Chassis. My son has a custom comp build, cost him a lot of money. After I replaced my motor with a great motor that has the Esc built in, and is brushless, my truck crawls everything his does. And for a fraction of the money.

Decent for the price. No instructions had to guess for links and screw sizes. Not enough m3 nuts in kit had to scrounge for my own. And link ends are very low quality. Will be ordering different ends. But for the price…. U get what u pay for.

I love this chassis kit and everything came together pretty easy. I do wish that I could find the links separately though because I have a 4 link setup. Other than that it is an awesome kit.

Allowed for more difficult lines that could not be done before with the stock chassis and shock mounts. A little bit of tinkering needed. I transferred over my 2021 Bronco. Good value when shock towers alone will cost this much.

Took it out today and had the left chassis rail snap on me right where the pan hard mount is. This is a weak point. So this kit is now useless to me after only a hand full of runs on it. Was contemplating buying another to replace the broken rail but won't be doing that. Injora makes some decent stuff, but this one is a miss. Never mind what everybody else has been saying about the complete lack of instructions and missing hardware. This was a huge PITA to put together in the first place.

Modification de crawler c’est le troisième que j’achète. Entièrement satisfait. Merci .

The media could not be loaded.  I bought this chassis setup in November and absolutely love it!!. It makes the center of gravity ALOT lower making it to crawl better. The carbon fiber is strong. It holds up to bashing around on 2nd speed. I do have lots of brass in the front

Missing some m3 locking nuts but other than that everything was there, seemed to bind a tiny bit so I used some of my trx4 link ends that were bent instead of straight and that seemed to help it out, very nice kit tho for the money.

No issues with the chassis won 2nd place in a competition last summer it's a good price it does the job

Missing a few links including the front ones to go around motor missif 2 upper rear links