SUNLU PLA Filament 1.75mm, Silk Gold 3D Printer Filament, 1KG 2.2 LBS Spool, Shiny Metallic PLA Silk Filament

I’ve had great results with this filament: it adhere very well to the print bed and all the reels come with a nice clip for the end of the remaining filament to anchor to the edge of the reel when you’re done. The bags that the reels come in are ziplock and can be reused. They put a lot of thought into these reels and the filament. It’s about as good as you can get and for the price you’d have a hard time finding a filament that is better than this. Highly recommended especially if you’re looking to get into 3D printing for the first time. Eliminate any frustrations by minimizing suspicions about your filament being the problem. This filament is reliable and perfect for beginning 3D printing hobbyists.

'A Good and Superb PLA!'Frankly Id heard many fine things and some favorable comment on SUNLU Filaments!So having bought a roll an done a project I can Honestly Report that most of the favorable things reported are in truth correct as it is a 'Very Fine' Plastic and SUNLU definitely has its act together!!!.PROS:Makes a Neat an Classy looking Part!Easy to Run, Easy to Set Up!Its the Real Deal You Get A Full Roll of !st Class Filament!Almost the Only Silk PLA Plus+ on the Market!!!!!A Real Bargain as the Price is Fantastic for what you get!.Fast Amazon Shipping cannot be Beat!!!!!CONS:None actually cept If Id known this was a PLA+ Id have ordered it sooner!!!!!In General:Now In My Useage The SUNLU worked and printed quite well.Setup was simple, I use Sticky Blue painters tape.Set Nozzle at 259 and Bed 109 and let warmup for 10-15 mins.I set 1st Layer at Nozzle 257 Bed 100, Speed at 35 or 40!Then after 1st layer is down and hard I set the rest of the run at about say:Nozzle 250- or 255 Bed 60 0r 75 and let Speed run at 45...True "I Know" at those settings Ill get some stringing but 'I dont have any problems with layers not bonding and It don't take 'All Day' to get the part finished either.Yes I know there are all kinds of 'Micro-settings, But I know that most machines have there own 'Pet Settings for wanting to run right.Now most folks want to run 'Cold and Fast' But I tried that and got a LOT of junk parts!.For me I found that "Slow but Hot" seems to get 'Better Parts'.....Me I adjust my speed with a New Plastic until Stringing starts to appear then I back off fast!.I also run my tests a 'Bit Differently' as many will run a ducky or a benchly and its a good way.For Myself I have a small but 'difficult part', See it dont take much Plastic but if the plastic is good enoughto make a 'Difficult Part' then the easy stuff will run Home Free as the SUNLU did!!!!!!!!!!Now One Major Complaint w Sunlu is it doesnt extrude well or the teeth dont grip the Plastic right!.Yes at one time 'I Had' that issue but here is how I worked around it!.A HOT TIP:Now sooner or later when the teeth wear down you will have to replace that drive extruder gear!.On most new machines its the round Brass One w the two small allen nuts sticking out the top side!Most guys re install the gear wrong, I know I did??????Yes I did as most of us will do what the YouTube guys did as they 'Set It' Plumb in the middle!.Hey if you are satisfied and it works for you go for it!!!!!!!!!!But there's a Better Way, In stead of in the Middle I just slid the Gear down a notch and let the plasticrun off the teeth on the Top Side of the Gear as it grips better and runs smoother too.Oh yes it will surely wear like they all do in time, But if you did it right there is no great need to replace the gear not by any means sic!!!...Just loosen the allens then "CAREFULLY" slide the gear back upwards until the Teeth on the bottom which are still good are NOW gripping the plastic as I think its pretty neat to reuse and get good service from the same part twice!!!!!.TO: Close;SUNLU Silk PLA is super good stuff that is easy to set up, It runs fine and makes a good part!.And to Finish Its the only PLA+ that runs a silk fibre so it has Very Considerable strength and I definitelyIntend to try some Printer Gears with this and the smooth finish makes a classy looking part too!.Kudos to the Seller!Kudos to Amazon!Nuff Said...IndianaED

This filament has worked well for all the printing I’ve been doing (prototypes, mostly) and is a great value.

Ive purchased PLA from this company before and loved it. Lasted forever and was good quality.I came back purchased the same brand but a different color. Same material type but different color.Now on the same printer many several settings later. Lots and days of trouble shooting later and nothing is working.Adheres to plate, prints 3 layers fine then some sort of extrusion issue occurs and the filament bubbles regardless of tempt of printing, bed, fam speed, print speed, or extrusion speed. It reliably fails and prints crap. It officially is the worst filament I’ve purchased and i will not purchase again.

Muy maltratada la caja, pero el producto está en buenas condiciones, se imprime fácil y da buen resultado. Parece que tiene un porcentaje bajo de fibra de madera porque el aroma al imprimir es mínimo y en la textura de la pieza impresa tampoco se percibe mucha diferencia, pero igualmente el resultado de la impresión es bueno.