LIANLI O11DE-1W Vertical Graphics Card Holder for O11 Dynamic EVO White, PCI-E 4.0 Riser Cable Included - O11DE-1W

Wasn’t sure whether this would work as I use the case in reverse mode and most ads say it doesn’t but thought I’d give it a try.3090 fe was 75-80 under load in reverse mode and I think it was because the exhaust fans on top were working against the gpu fans.Now, since the air from the gpu is exhausted straight through my side fans/rad I am 65C under load on the gpu and my ssds are almost 10C cooler whilst gaming too. My cpu runs at 40-45 (5-10C cooler) on hogwarts legacy, but does run at 58 and 70 on warzone and need for speed unbound. Due to the dropped temps, my system is now quieter too.I’ve not noticed any issues with either physical stability (I’ve used every screw possible to hold this in place and I might even look into getting a long metal L bracket to hook up to the anti sag bracket if problems arise) or with the pcie riser cable either. This made more of a difference than when I went from 6 fans to 10.

Allows a card to be vertically mounted, fits case well, and uses multiple screws for mount.It is possible to mount with gap underneath, leaving space for fans.This should be priced at much less given its a bit of metal and a pcie 4 extension.

I have the O11 XL case and it fits in there too. Nice and easy to install & no issues with my MSI 3060Ti. It nicely fits and safely secure

Its an original Lian Li part so all is well. Buy with confidence.

If you guys have a 4090, replace your front glass panel with this. You will not regret it.

good thing i waited to review this bracket and riser cable. (otherwise it would have been a 2-3 star review) because i waited, that cable that was detected as pcie3. is really pcie4. a driver update seems to have fixed the detection (rx6750xt, x570 motherboard) or it could be that the cable end has to be perpendicularly connected to the motherboard pcie16x (or straight out)…i modified the bracket so i could use another riser cable. it worked, it did not work, it worked after i pressed down on the riser cable connected to the motherboard to straighten it.as it turns out all of the riser cables that i have now get detected a pcie4. (and actually the lian-li cable included is the fastest… 24 gb/s… strange stuff, was cursing everything)the bracket is really nice. In a lian-li lancool III case, you can raise and lower the bracket to allow clearance below the bracket. i ended up using the lowest setting to give the cable room.I added struts to the bottom of the bracket to prevent sagging, and the rubber spacers on top to keep the . watercooling block level , and not stress the gpu circuit board… normally you do not have to worry about this because the waterblock has a back plate but the back plate would not fit on my gpu (not because of this bracket)only disadvantages this bracket could have is that it covers up your motherboard slots except for the bottom ones,good thing using this bracket is that it sets the GPU away from the side glass. moot point if you are water-cooling. i mention this because there are cases with vertical slots, but they place your gpu right up beside the side glass.OTOH lian-lian has a 4slot bracket… probably a better idea if you have an air cooled card.

It's just good.Since I changed my case to this lian LI, my video card barely turns on the fans.Also I see people complaining about the PCI express extension, but for me it's fine. No need to buy the 600mm

The LIANLI O11DE-1W Vertical Graphics Card Holder is the ideal solution to accommodate your new 4090 graphics card in your current case. Designed specifically for the O11 Dynamic EVO White case, this vertical graphics card holder allows you to install your graphics card in a space-efficient and visually appealing manner.With easy installation and a secure fit, this holder ensures optimal cooling and performance for your high-end graphics card. Upgrade your gaming setup with the LIANLI O11DE-1W Vertical Graphics Card Holder, and enjoy a seamless and powerful gaming experience.