Monster

My Simpson pressure washer came with a 25 foot hose, which while decent, isn't rally long enough for me to reach every corner of my patio or driveway. I bought this one because it was the same as the one that came with the pressure washer, just longer and it turns out that the 50 feet is just want I needed. And, if I ever need more, I can just connect the two hoses and have a 75 foot reach. It's sturdy, well made, does not leave any marks, but it is a bit stiff (not sure if there are really any quality pressure washer hoses that are super flexible). I do find that leaving it in the sun for just a few minutes helps. But, I am satisfied and would buy it again if I had the need.

Great medium-duty 4500psi 50 footer. Comes with 3/8 inch QC couplings, male on one end and female on the other. Includes the o-ring, and it is installed on the female coupling. Also has bend guards on each end, as shown in the picture. Note, this is for higher-pressure machines. This will not work out the box for mid- and lower-pressure machines, such as most every electric washer and most every 2500-3400psi gas washer. It is not the products fault if you order the wrong hose/connectors. You should order this if your setup uses 3/8 inch QC couplings, such as you would find in most every machine above 3500 or so psi. Check your machines specs first before ordering. This will not work out the box with 1/4 inch or 5/16 inch hose setups, unless you change the connectors on this or your system. The hose itself is rated 4500psi. My machine can do 4200psi/4.0gpm. Always, always, always, lower the pressure on your machine when testing new hoses. If the hose bursts or a connector comes undone, this can be a very dangerous situation. Start low and check the entire length of the hose. Gradually increase pressure and re-check the hose. Keep raising it until you reach your desired working pressure and re-check the hose. Use it for a short while and re-check the hose. Really, you should be doing this every time you use your machine, and not just when the hose is new. Its smart and safe. The hoses themselves are high-quality, but I would not say pro quality. These hoses are too flexible for day-to-day use and abuse. These are the kind that will easily kink and ruin themselves if you are not careful. Don't get me wrong. I am not calling them cheap. They are good hoses. However, compared to other comparably-priced pro-level hoses I have had in the past, these are not the best. As long as you can keep them from kinking, they should be fine for many years. As for corrosion in the braiding. First of all, make sure to roll up your hoses in such as way as to allow the water to drain out completely. It takes practice, but you can get most of that water out. Also realize that all hoses have this "problem." Its just that you usually cannot see the braid. These are translucent, and that's why now all of a sudden you can see it. If this is really a problem for you, I would recommend you leave the pressure washing thing to the pro's. Really, this is not a problem in itself. Its normal. Bubbling hoses are bad. Rusted braid, eh, not a big deal. I was able to use two of these plus the OEM 50 footer, for a total of 150 feet with my machine no problem. Still had great pressure at the tip. If you need a long reach, just buy more 50 footers. Do not waste your time, effort and money with 100 footers. 50 footers are better in every way except price. Well, price at least in the short term. In the long run, 50 footers are cheaper. Also, 50 footers allow for easily customized setups. If you only need 50, then only use 50. Add more as needed. Also, if one bursts, its not the end of the show if you get my meaning. When a 100 footer bursts, it hurts your feelings. Also, 50 footers are easier to clean up at the end of the day. I did this as a business for many years. Trust me, stay away from the 100 footers.

I've had this 150ft hose reel for about a year now and it hasn't broke on me yet, I have probably used this on 20-30 jobs and it's held up. Great pressure washer hose, very flexible, weighs nothing, overall great product.

Does not kink, it'll just coil at most. Its a heavy hose. Recommend getting couple 50ft or 25fts and connecting. Pain in the uknow whipping around 100-150ft hose. Quality of hose build is great, very durable. I use with my 4gpm 4500psi washer with ease. Product appearance look just the photos. Probably one of the better priced hoses.

This thing is a beast. Bought it for my PW business. Great quality, fittings are beastly, very heavy. I will report back on leaks, definitely looks pro/ clean looking.

Works great. Great length options.

Great for small jobs. Not too heavy so transporting is easy. I haven't had any problems with leakage. Excellent quality.

Very good hose functionally. Coils smoothly and reasonably light and kink resistant. The only flaw is the non stainless braid they used. Mine wicked moisture into the braid and caused black rust stains 2 meters up the hose (so far). It has not yet caused a failure, but disappointed in it.

Have had this almost a year now. Bought it to extend the range of my heavy-duty 3300 psi pressure washer and replace the original (shorter) hose it came with. I can leave my pressure washer on the ground and with this hose, wash the entire upper deck of my house. The deck is over 40 feet long and 8 feet above grade. This is a tough, high quality hose and while it is flexible, I recommend laying it out straight (uncoiled) before connecting it to the pressure washer/wand. Once it is under pressure it will tend to hold its shape, making it difficult to uncoil. Came with the appropriate 1/4 inch connectors on both ends, as shown. Not all hoses do!

My husband loves this high quality hose!!

A little expensive but a great product so thats ok.

Better than expected.

I have purchased many of these for industrial use. They have lasted longer than more expensive ones I’ve bought from industrial suppliers. Gets a little stiff after a lot of use but good value for the price.