Router Bits Set 1/4 Inch Shank ,70 Piece Router Bit Set,Tungsten Carbide Router Bits Kit for Professional Woodworking

For the price, I knew I wasn't getting top quality router bits, but this is a very complete set of basic bits. My plan is to find the ones I use the most, then over time, replace the with top quality bits. Some people have complained about the bits being scattered all over the box during shipping. I didn't have that issue. The manufacturer is now putting some sort of adhesive on the shafts, so they stay in place. The down side to that is they REALLY stay in place. Use extreme caution removing them, as they are very well stuck in the case holes. I am using an adhesive remover to clean each one. I have also built a bit case that fits my needs & I oversized the holes slightly so they are easy to get in & out. The bits I have used so far seem to be sharp & cut well. I'm guessing they will dull over time, but for a little over $2 each, I am okay with that.

Great set! I bought them mostly because I had a project for my church, and needed maybe three of the styles, but, for the price, I decided to go for the whole set. Cut quickly & smoothly, no problems.... Plus, I hung the case on the wall of my shop, and it makes a nice display piece. Came with a poster of all the bits, which my kid promptly stole & hung it in his "craft area"

You get 70 carbide-tipped router bits for less than $2.25 each. They may not be as good as Freud bits that cost $30 to $40 each, but they're definitely worth the price of this set. My intention was to have the storage box and the large selection of common router bits and then replace the most used ones with really good Freud bits when they wear out. I think now that that may not even be necessary.

Theses are awesome router bits

Love the bits and the case. The only thing I would have done a bit different, would be to utilize both sides of the container and spread the bits out a bit more as some are difficult in pulling out of their perspective area without busting your knuckles on the other router bits.

Good bits for $$$

Great presentation. This set was beautiful presented. 1.Heavy pine box with finger joints on corners. 2. Heavy latch. 3. Medium duty hinges. 4. Each router bit is mounted in its own plastic sleeve not just seated in a hole. 5. Each group of bits has an illustrated profile of the cut they will make printed on the shelf and covered with protective plastic cover. 6. The opposing door has a clear plastic cover designed to protect each bit. I'am totally blown away by the chest. I will replace the hinges with a piano hinge. I have not been able to use any bit. Yet if the box is any indicator of the quality of these bits l should be satisfied.

It's hard to be fair when I've only use three of these bits so far.but what I've used was sharp and seemed realy nice so far.cant say more then that and be honest not used them enough yet.i can up date in a mounth or two.

The 1/2 inch set is very good

I am planning to do a lot of DIY projects and I already have a router for 1/4 and 1/2 inch shank, I have read and watched that recommended is to use 1/2 inch and while looking on for a more practical choice as a beginner, I came across with Kowood 70 bits, some of the cons in while reading the review is that the packaging is not proper and might be damage during transit, however, I receive the items with all the bits in its proper places, there is a plastic that holds the bits in place , all the bits are good and sharp and sitting on their slots tightly, it took me sometime to figure out pulling them without cutting my fingers, really need to be careful as the bits are really closed to each other, all in all, I am very happy and cant wait to make design out of it!!! Update: Need help, may I know the size of collet that will fit this bits as I cant fit it in my bosch 1/2 collet, I measured using caliper and the shank is bigger than the collet, can somebody point me where to buy 12.7 dia collet as it may be the right size for these shanks, thanks in advance.