SUNPIE Smoked LED Tail Lights for 2007-2017 J eep Wrangler Brake Reverse Light Rear Back Up Lights Daytime Running Lamps DRL

The media could not be loaded.  Id like to send a review in because of how much I enjoy these on my jeep. I had got the clear lens versions and instantly returned them because these looked better. The lights are bright and come installed with resistors to eliminate the hyper flash. no fog in the lens after driving in heavy rain. 5 stars for sure. highly recommended. I decided to go with the blacked out theme on my jeep. This includes tinted windows dark rims, black paint obviously dark headlights taillights, turn signals, you know just about everything black. These were a great addition to the overall look of the jeep. Ive washed it a couple times since the install and they don’t seem to be scratching like other cheap lenses do.One thing I do have to say about these, is that because of the darked lens, it does change the color of the light a little. They are a little darker colored, but it does not affect the actual brightness of the the led lights. I have not taken the jeep off roading or in the mud yet, so im not quite sure how these will hold up. I mean if these get slammed into a tree full force, I don’t think these are tree resistant, but I mean, for everyday use, driving on the roads, impressing your friends. Sure, throw em on your pavement princess and let them rip. I also installed the tinted turn signles. These are much of these same quality. No issues installing them or the quality of the light/lens. I would recommend these to anyone as well. Just pop out the old ones, pop these ones in and enjoy the new look of your jeep. Both the tail lights and turn signals took 10 minutes to install, and that was me taking my time.

These are plug and play only if you want the outline LEDs to be your brake light and the block of 12 LEDs to be the running light. Personally I want more brake light. Not sure about the green and purple wires, mine did not have those. Had to switch the yellow and red wires and now the large lights are the brake light and the outline is now the running lights, Luckily my neighbor had the terminal removing tool so it was an easy switch with no splicing and soldering. However, now they hyperflash and I will have to order the load resistors to get back to normal blinking, haven't checked the OBD to see if it is throwing a code. They do go on easy and look nice. The lights are bright and should help grab attention when used. I'll update if there is any change or if there is any moisture that get into the lens. At the moment I consider them worth it even with having to get the 4 dollars of load resistors to correct the problem.Update: Installed the load resistors (cost about $2/ea) and the hyperflash is now corrected. The company sent me an email that they were disappointed in my negative review. I don't consider 4/5 stars negative and I also don't believe the company is paying attention to all of the comments regarding the wiring issue. I just purchased the fog lights for my Jeep from the same company.

First off let me say that the seller was great and communication was prompt. This review is strictly about the item itself. Lets start by saying these look great on my black jeep. I have purchased other Sunpie products and couldn't be happier. These lights would fogged up every day even though the vehicle was stored in the garage. I first thought it was due to the guards that i have installed, so i ditched the guards and although the problem was better, they still fogged up. Another issue was that after installing them i did have a problem with the signals going into hyperflash. I have the front led lights installed and did not have an issue until installing the rear lights. i went ahead and removed the lights and installed the resistor that was supplied using the directions given. The issue was resolved until a week or so later. I would intermittently have an issue with the hyperflash, and eventually became worse. It started with the right side and soon became both sides. It would be at least a few days until i could investigate further. Coincidentally the next day i it ended up blowing the right side marker light fuse. I decided i better look into it. I removed the right side tail light and first noticed that the resistor was very hot. I decided at that point due to time issues i would just put the stock lights back in until i could look into. I replaced the right side and moved to the left. Once i pulled the left one out, it was immediately noted this would not be a quick fix. the entire tail light plug was melted into a black ball and I would not be able to salvage it. The resistor wire was melted and exposing bare wires in parts, but did not appear to come in contact with any body parts. I ended up having to go to a wrecking yard and splicing in a new taillight pig tail. Keep in mind i was very diligent when i installed these as they are basically a plug and play unit . I made sure there was no chance a wire could come in contact with the body. I even ditched the cheap splicing connectors when installing the resistors. Again, There was no problem with the seller. I will likely Not replace the units as I am a little nervous about my wife's ability extinguishing electrical fires on the side of a highway.UPDATE: Manufacturer has agreed to replace the units free of charge as long as I update my review. I will try installing them, but if I experience the signals going into hyperflash, I will say I will not be installing the supplied resistor and go down the same path as before. I absolutely refuse to burn my rig to the ground over a pair of eighty dollar taillights for the sake of looking great.UPDATE: Manufacturer never sent replacements due to I would not agree to changing my rating to five stars prior to receiving them.

I like the product, it looks high end BUT they should have included a rubber gasket that goes around the back of the unit that goes between the unit and the paint of my Jeep.I do see a small gap at both upper corners where weather can get in and that rubber gasket would prevent that from happening.You make what appears to be a high end unit you should add the gasket and get 5 stars for making the complete process High End.Part 2: My passenger tail light went out. This company sent me a replacement but replacement was not the same as the driver side. I had to wait a few weeks to have them correct the problem which they did through much email communication back-and-forth. I raise my review up one star to four stars for their consistency.

These look good and would be a drop-in replacement for the OEM lights with no guards. If you have guards like I do, then you will require longer screws for the outside 2. The inner ones that attach the light to the body are long enough.When I opened the box, I noticed that the right light had the one of the side marker lights not attached. I removed the side spaced plate and noticed the glue had let go. I applied a little glue and it was fine. We will see how they hold up in the car wash.The lights work well but the side LEDs are connected to the signal and flash. Since there are 2, one could flash and one could be a marker. I may rewire them in the summer to do that.Sunpie are the same brand as my headlights and their customer service had been good to deal with.I am hoping to have fewer issues.These are respecting my Spyder LED lights that had LEDs on the side and right that were intermittent.

The lights look amazing and were very easy to install. Unfortunately, the driver’s side had scuff marks on the side so I had to re order the lights and will return the damaged one. Otherwise this would have been a 5-star review. Well I received the replacement tail lights today and they have the same scuff in the same spot so its defect from the way they are made so that deducts another 2 stars. I will revise this review if and when the seller reaches out to me with a satisfactory response.Install Tip!I had gone to the local bolt supply shop and bought stainless steel screws and painted the heads black before I installed these. You will need 4 #10 1 1/2" and 4 #8 2" stainless screws. The shorter screws go on the side closest to the spare tire and the longer screws go on the side farthest away from the spare tire. As well when you remove the old lights, it’s a good time to clean where the lights were and use touch up paint as needed around the screw holes. I also used dielectric grease on the electrical connections just in case any moisture finds its way into the electrical connections.

Les lumières ont une petite ballasse prévu pour être installer sur une braquette fournis avec le produit, Il y a rien sur le Jeep pour recevoir cette braquette. vous devez percer ou coller au choix. Personnellement j'ai ajouter de la protection sur les câbles qui sont peu protégés VS ceux sur le Jeep et à mon goût personnel. Mais le produit est génial, facile d'installation pour un bricoleur débutant et le look est super.

Great lights but the only issue I had was that the fuse/resistor got too hot that it melted the plastic if it got too close to the light housing.

These tail lights will most likely be the easiest upgrade that I have installed on my jeep. It took less than 10 minutes and they look great and work well.Update: Dec 30 2020After just over two years these light are failing, they are burning out and now I had to put the original tail lights back on my jeep until I find a better set. I love the smoke lens look but they dont last. I fist noticed that the passenger side had condensation in it after about 6 months of use, then the bulbs started to burn out..