Question 1

would someone please change the picture to the right vice? I am not going to buy until you care enough to correct your mistake.

Accepted Answer

My vice matches this picture....

Question 2

What country is this made in?

Accepted Answer

Groz product is made in India.

Question 3

Can someone tell me the height from the drill press table to the rail where the workpiece would set at bottom of jaws?

Accepted Answer

JAW LINERS
Wooden liners expand your vise’s holding
capacity and prevent your work from being
marred by the cast iron jaws. Any
hardwood will work as a liner material. The
front jaw liner should be at least 1 5/8”
thick to prevent deflection and so you can
drill holes in the top of the liner for bench
dogs if you like. The rear jaw only needs to
be 3/4 – 1” thick because it will be
supported by the edge of the bench. For
small vises (7” wide), make the liner length
12 – 14”. Medium sized vises (9” wide) can handle liners 14-16” in length. You can go up to 18”
long for large vises (10” wide). Anything longer will cause excessive racking and shorten the life
of your vice. In the end, the jaw liners need to be at least 1/8” above the vise’s guide posts to
allow for seasonal movement and flush with the top of the bench. However you choose to
attach your jaw liners to your vise, make they can be easily removed if they become damaged
or warped. At this point, close the vise and make sure the liners mate up acceptably and shim if
necessary. Remember, the jaws of these vises toe in where they meet at the top and should do
so after the liners are installed.
MOUNTING THE VISE
Depending on your bench’s top thickness, you have two mounting options. If your top is at
least 2” thick, lag screws work fine. With washers attached, run the lags up from underneath
the vise’s carriage, through the spacer block and into the underside of the bench top. If your
top is less than 2” thick, install carriage bolts right through the bench top and secure them with
nuts and washers under the vise’s carriage. Be sure to countersink the heads of the bolts below
the surface of the top to prevent tool or work damage. Plug or fill the holes by any method that
pleases you. With either mounting technique, you’ll want to occasionally check the hardware to
be sure it isn’t working loose. As for maintenance, lubricate the threads of the main screw with
light oil and wax the guide rods occasionally.

Question 4

What is the center to center distance between the hold down slots in the mounting base?

Accepted Answer

The center to center (front to back of vise) is 3.75" +/-.  Nicely made tool, with a high rabbet on the jaws for holding thin material.

ASIN	B077XN118X
Best Sellers Rank	#126,035 in Home Improvement ( See Top 100 in Home Improvement ) #130 in Bench Clamps
Brand Name	Groz
Colour	Multicolour
Country of Publication	India
Customer Reviews	4.6 4.6 out of 5 stars (97)
Global Trade Identification Number	08901486351216
Importer Contact Information	GROZ NET INDUSTRIES, GROZ NET INDUSTRIES, Village- Kherki Daula, N.H. # 8, Gurgaon ( Haryana )- 122001 ; 0124-2827700
Included Components	1 Unit of Groz DPV/UG/100 Drill Press Vice
Item Dimensions	33 x 18 x 72 Centimeters
Item Type Name	GROZ Drill Press Vice
Item Weight	3.5 Kilograms
Manufacturer	GROZ NET INDUSTRIES, GROZ NET INDUSTRIES, Village- Kherki Daula, N.H. # 8, Gurgaon ( Haryana )- 122001 ; 0124-2827700, Groz
Manufacturer Contact Information	GROZ NET INDUSTRIES, GROZ NET INDUSTRIES, Village- Kherki Daula, N.H. # 8, Gurgaon ( Haryana )- 122001 ; 0124-2827700
Manufacturer Part Number	35121
Manufacturer Warranty Description	1 Year on Manufacturing Defects from the Date of Invoice
Material Type	Cast Iron
Model Number	DPV/UG/100
Number of Items	1
Number of Packs	1
Packer Contact Information	GROZ NET INDUSTRIES, Village- Kherki Daula, N.H. # 8, Gurgaon ( Haryana )- 122001 ; 0124-2827700
Set Name	Groz Drill Press Vice (1 Piece)
Style Name	Bench Type
Tensile Strength	500 Pounds Per Square Inch
Unit Count	1 Count

GROZ Drill Press Vice with Specially Designed Jaws| Ideal for use with Drill Stands, Bench Drills & Drill Presses| Durable| Jaw Width: 100 mm |Jaw Opening: 92 mm| Jaw Depth: 30 mm| DPV/UG/100

Details

Details

Description

Specifications

Common Questions