Diyco 2 Inch Digital Tire Pressure Gauge Lcd Backlight Large Display, Stub Style

Pros:1. Out of the package this feels like a really nice well built product2. Has a thick rubber jacket to protect the gauge (plastic) and the rest is solid metal3. Nozzle is 360 degree rotatable which helps for checking tires easily4. 30 second backlight screen which helps to check spare tires in the truck5. Test the gauge up to 65 psi and works well6. Tested against another well built pencil gauge at 32psi and varied by 0.5 psi (accurate)7. Gauge auto turns off to save batteries8. Gauge auto turns on and will display pressure (No need for an ON button)9. Can reduce the pressure with the bleed off valve to set the pressure quickly with instant read out10. The bleed off value requires reset after each use but then will leave reading displayed until reset which is valuable when checking tires in difficult locations.Cons:1. The two coin cell batteries are very difficult to replace. a. Takes 7 screws to get to the batteries b. The display circuit board must be removed and is very difficult to reposition for alignment c. The battery wires are welded to the batteries d. The batteries are difficult to then remove from the case e. There is large chance the gauge will be broke when attempting to replace the batteries and will become useless f. The initial battery voltage when new is 3.01 and 3.32 so one of the batteries is already going bad g. Cannot tell the battery size because it is labeled on the other side and feared destroying the device. h. With luck was able to reassemble the gauge and get it to turn on after about 15 minutes of playing with it since the circuit board placement is critical i. My last unserviceable digital pressure gauge batteries lasted (5) years and then went into the trash can because of the welded batteries2. The gauge must be turned off and then on every 30 seconds to get the backlight turned on again between tiresItem received at a discounted price in exchange for giving an honest, unbiased report.

This gauge seems to be accurate and consitant. It's fairly easy to read in most light conditions. The angled swivel takes a bit of getting used to, though. At least the stem is all metal (unlike some cheaper gauges). The whole unit seems well made.I do like that it can read up to 200psi. That makes it good for commercial vehicle tires, as well as road bike tires.The angled swivel is almost a necessity for a gauge of this type, but it can be a bit awkward to keep it on the valve stem, andpress the air bleed valve at the same time, and still see the display. It takes some practice...Overall, it's a pretty decent gauge. Time will tell about battery life, and how well the whole gauge lasts with age, and use.

Works well, great value for the price! Gets a reading and a tight seal quickly. Also the swivel head helps a lot in getting past the varying angles of spokes. I have a 78' Honda CX500 Motorcycle and this works great getting around the Comstar spokes. The release valve helps get you an accurate PSI as well. The only con is that the rubber jacket around the gauge is flimsy and peels off easily.

Worked well until I had to replace the batteries.Backlight and display function, but it will no longer register pressure after battery replacement.Lasted about 2 years.

Very good product. I compared readings to other gauges, and this one is accurate. Seal with tire valve is good, so you get an accurate reading immediately. The backlight may turn off while in use unexpectedly, but this is a battery saving function. You can turn it back on by pushing a button. No need to reset the gauge as I first thought. This is explained in the instructions on the box, so be sure to read them.

Seems to work fine. If I am checking all 4 tires, the light will go out and I need to turn it off then on again. The time delay for the lighted display could be longer.

Very fast shipping aand easy to use. I am concerned about accuracey. Gauge reads 3-5 psi lower than vehicle sensors and manual gauge.. I will have to test against other digital gage

It would be nice if a eyelet or hook was incorporated in the tool so that it could be stored easily.