Valley EnterprisesFTDI USB Chipset CI-V Cat Control Cable Compatible with Icom CT-17 – Length: 10 Feet - Compatible with: IC-7300, IC-7610, IC-7851, IC-9700, IC-R8600, IC-R9500 (See Complete List)

This item was ordered on Sunday of a national holiday weekend, and it was processed on the holiday.It was shipped out, and arrived in two business days with standard shipping to the East Coast.The item worked perfectly on the first attempt including downloading the driver from the Valley Enterprises site.The 10-foot cable version was purchased so there were no issues with the distance between the computer.Background–The motherboard had a serial header and the 9-pin RS-232 port but no matter what was done, the comm port would not work with the CT-17 generic interface. It worked before with a different motherboard and 32-bit operating system.On the newer, in-house built computer, and 64-bit operating system, the comm ports were disabled in the BIOS.Then the driver software, downloaded from Valley Enterprises, was installed. After the driver installation, the Valley Enterprises cable, the CT-17 version, was connect and everything worked.There have been zero, no issues in using the cable doing on a month.

Works great with my Icom 751 and Ham Radio Deluxe.

Seamless installation under Windows 10, and works perfectly with my Icom IC-706II. I simply followed the instructions and loaded the FTDI driver software in advance of connecting the interface to my PC then set the appropriate addresses in software to match my radio. This is a great solution to allow use of newer computer equipment (that don't have an RS-232 serial port) with older radios using the CI-V interface for rig control - without the use of USB to RS-232 adapters and all the pitfalls that can come with it. There may be cheaper options out there, but this interface uses a genuine FTDI chip and is well-made.

This cable works fine with my PC and my IC706MKIIG using Ham Radio Deluxe to control the radio. Of course the IC706MKIIG doesn't support all the possible features available for newer radios, but setting frequencies into software memory is simple and effective. It does NOT, however, allow programming the radio's memory channels since the 706 does not support doing this. The nice thing is that several memory groups, offsets, and modes can be set up in the Ham Radio Deluxe control software to use when connected to the radio. This includes scanning, etc.The 10 foot length of this cable is quite handy for my particular setup since my computer is somewhat remote from the radio's location.I have not hooked up a TX or RX audio link into Ham Radio Deluxe but this can be done using various interfaces available commercially or shown online on the internet for the DIY folks. These functions, of course, do not use the USB cable but are supported on the 13 Pin DIN Male Connector used for auxiliary Keying, TX AF, RX AF, and other circuitry and functions.

I've used a couple of these. Stable CI-V for Icom radios. Real FTDI chip. Not cheap, but good value.

I bought this cable to interface my new Windows 8.1 laptop with no serial ports to several pieces of Icom equipment. It worked as soon as I plugged it in. No driver issues or other problems. It just works. One thing I found was that my Bluetooth interface built into the laptop used up most of the COM ports between 1 and 20. Since I have a few programs that cannot be configured to access high COM port numbers, I temporarily disabled Bluetooth and it released the lower number COM ports for use with this product and a couple of other FTDI based USB to serial converters. I then re-enabled Bluetooth which automatically populated the higher number COM ports. I have the CI-V, serial converters, and a USB sound card connected to a USB hub so that by plugging in just the hub cable, I can use rig control, rotor control, PTT, and digital modes.

Ehhhhh, NOT recognized by my computer, certainly NOT FTDI!

I was having difficulty using digital modes with my hf radio. I ordered this, installed the cable, installed the driver from the manufacturer, & immediately made my first psk31 contact. Not sure what I was doing wrong, but the ci-v cable to my icom 718 seemed to cure it.

Snabbaste FTDI chipet, Grön/Röd LED som visar aktiviteten, funkar direkt plug n’ play i Windows 11 utan extra drivrutiner 🙂👍🏻KÖP! 👌🏻

It does work as intended and without problems with my IC-718. So far, so good and believe it is ok work any COM rig having the CI-V feature.