Swingline 37201 Heavy-Duty Staple Remover, Satin Chrome Finish - S7037201A

This isn't ideal for use on thin stacks of 2 or 3 papers. Use a claw or the slide in remover for that (the slide in that increases in thickness over the trunk).This removes staples from thin (not too thin) to thick stacks well, easily.There's a way in which it works perfectly and a way which causes staples to break. There is a toungue like metal piece in the middle and two flat parts (arms) on either side of it. The tongue slides into the staple, DO NOT shove it in so far that the two arms are next to/touching the sides of the staple. If you do, it will act as a sheer, breaking the staple on both sides. Every time I've done this, the staple breaks. If you pay attention while you're doing this.Slide it in slightly (like 1/8th of an inch or 1/16th of an inch) and it will work perfectly. If you're dealing with a particularly thick stack, a long staple, first apply it to the back of the stack, pry open the arms of the staple, then do the front.I see no reason for the bad reviews (at least, not on the device I received) or complaints about this thing being wild & crazy and flailing all about. It's simple. Just do it, be calm, look at what you're doing. It works. You'll figure it out.

Better than sliced bread! Seriously, I had been using the standard "contemporary" stable removers and they were a pain. I got this one and it is fantastic. Makes the job so much easier. The only thing to be careful about is that if you are removing staples in order to use a multipage scanner, like the Epson scanners, you will find that once the staple is removed, you get a slight raising of the papers around the staple holes that cause the paper to stick together. If you put it into a multipage scanner without separating the pages first, you will get a jam, since the pages will stick together. The solution to that is to use the standard "contemporary" staple remover to straighten the staple ends at the rear of the paper and then use this item. Then, no problem with the sheets sticking together. When that is done, the item is great and you also don't have the problem with tearing of paper with small number of stapled sheets, as has been mentioned by others.

Purchased this for removing heavy duty staples I installed and it works well.

This staple remover is a very good staple remover after I made a slight modification. The modification that I made was to grind down the end that slides under the staple to make it thinner on the forward edge so that it slides under the staple better. After making that mod it really works well. The thing that I really like is that it grabs the staple and pulls it out so you don't have to use pliers, It is very heavy duty. I am a coin collector and I used this to pull out the staples on those 2x2 coin holders where the staples were small and tight.

I bought this to remove staples from carpet padding on a hardwood floor. Works extremely well, takes them out in one piece. Saving so much time and effort.

Sturdy, easy to use, and takes out giant staples for thick stacks of paper no problem. I love this product. I am an archivist who works with reports and has to remove staples from old ones since they are not archival. This makes it easy to get these giant staples out of reports of hundreds of pages without difficulty and does very little damage to the paper. If you are removing regular staples from less than thirty pages, I would reccomend getting another tool, like a flat staple remover.

Works great, sometimes you first have to lift the two edges of the staples and then lift; otherwise the legs of the staples may crack, and you have to pull apart the sheets to remove.You have to stick the 'tongue' of the remover fully under the staple so that the two legs of the remover surround it - like that it gets leverage.But the springs that hold it straight, cracked. Swingline gives a lifetime warrantee on its products, I believe, but I have had better experience with Ktrio Staple Remover Professional, it is easier to maneuver than a large remover like this .So, this remover looks quite fancy and it may have its place -- you can see a lot of people are happy with it, but I was happier with those (pen-style removers, I have found those better than the 'alligator teeth' as well. )

So, I bought this because I hate using the alligator style staple removers and that was all that was available at work. So I deal with a lot of departments and their receipts, and all the departments staple their receipts REALLY STUPIDLY, and the alligator style staple remover I was provided with was driving me nuts. So I bought this. It has SAVED MY SANITY. I mean that in every sense of that statement. These staples were so screwed up, I was actually losing it.Then this staple remover came, and it pulls staples like a DREAM. It pulls ANY staple out of paper like a scalding knife through melted butter.

Es un quita grapas muy práctico y es de muy buen material

Funcionalidad

Simple to use, the Swingline Heavy-Duty Staple Remover makes short work of 14 and 11 millimetre staples. Works straight out of box. My one piece of advice: for thicker documents, lever from the back first. Doing so, will avoid ripping sheets.

Il prodotto è valido per un uso di ufficio, il problema che è mal rifinito nell'impugnatura perchè è lamiera stampata e bisogna stare attenti che potrebbe tagliare. Serve un colpo di lima...

Très pratique, efficace et costaud. Je recommande ce produit!!! Très voir excellent qualité, vu le prix. Ça vaut le coup!!!!