Set of Two 20x10-8 Lawn Tractor Tire Golf Cart Inner Tube 20x8x8 20x10x8 Lawn Mower Tire Tube

good price

First time installing tubes on these size wheels, though I have installed tires on 15"+ rims before. It wasn't easy but wasn't a drawn out frustrating process either. I just used long prybars and big flat screwdrivers. It requires you to understand how tires fit over a rim, and you can't just force it. If you haven't done it before, watch some youtube videos to understand where to place the tire, and where to pry. If you're detailed, patient, and even slightly mechanically inclined, you can install these.I installed one on a wheel I took off the mower. I installed the other on a wheel still on the mower. It was actually easier to install with the wheel still on the mower, as that's one less thing that can move around.I had tried slime in my old cracked tires but it was leaking out of the cracked sidewalls. I left some of the slime in there when I installed these tubes, I figured it would give a bit of lubrication between the tube and tire, and maybe even prevent flats later on. I've done about 6 full days of driving around mulching and towing a rake on these tires since I installed the tubes and they hold air perfectly. Not turf, lots of uneven terrain, lots of brush and sticks and rocks, lots of unintentional burnouts, no problems whatsoever. I run about 8 psi for better traction.I'm pretty thrilled to have kept a pair of old but full tread tires out of the landfill, and to have saved money and learned something in the process.For those searching I was installing these on a Husqvarna YTHK1542XPC aka YTH1542XP aka YTH 1542XP, which was actually made by AYP around 2004 and is also sold as a Craftsman.

An inner tube is an inner tube. It's a bear installing an inner tube in a small tractor tire. But the tube itself was no problem. And I noticed the valve stem is heave duty. I would purchase again.

Fit well on drive on mower, need to hold inlet valve whilst fitting inner tube as there is no retaining nut

The rear tires on my mower had plenty of tread, but would not hold air due to dry rot. Rather than spend $90 on 2 tires, I put these tubes inside the old tires and they have been holding air fine for several days now. I was able to install these without special tools. Break the bead on both inside and outside, then use a large flat screwdriver, pry the outside bead over the rim. Remove the tubeless valve stem. Slip the tube inside the tire and pull the valve thru the hole(I screwed on a cheap valve stem tool to prevent the valve from slipping out of the hole). Kneel on each side of the tire and use the big screwdriver(carefully) to pry the tire bead back onto the rim. Add air and you're done. Tools used consisted of a large screwdriver, a small prybar and a piece of pipe that fit the center hole of the rim.

These are the ones to order if you need the valve offset from the center-line of the rim. Yes, you can make the tube with the valve on the center-line work, but trust me, these make the install much, much easier.I followed the manufacturers recommendations of filling the tubes 24 hrs prior to installing to make sure they hold air. Not necessary, but why not? I also made sure to use Windex on the tire beads so as not to pinch the tube during install. I also had a set of 12" tire irons instead of using screwdrivers, which can be sharp when applying the pressure needed to roll the tire bead onto the rim. One final tip/suggestion is to feel the inside of the entire interior of the rim prior to stuffing the tube inside the tire. I came across at least three very sharp and fairly large and heavy paint burrs that I knocked off with a tap of a hammer and cold chisel. I could easily see a scenario where the tube could have been punctured by these burrs. One more little nicety worth noting is that each tube includes a small rubber washer that fits underneath the valve cap. Craftsman LT2000 20x8.50-8.00

Added tubes to my riding mower tires. No doubt these will now outlast me. Nice and thick. Heavy duty.

Was a Great Product for what I use it for and it is working in my lawn mower for the inner tube and it hold up air and ride like you are gliding on air, prefect size. I am very happy with this product well made.