ELEGOOUpgraded ABS-Like 2.0 3D Printer Resin, 405nm UV Curing Photopolymer Resina for Mars Saturn Jupiter MSLA DLP LCD Impresora Grey 2000g

I wanted to print the dolphin and did. It is hard to get it super clear as the surface, when dry, looks hazy. I may not be getting it clean enough, but I think some work with the 3M headlight cleaning kit will do the trick. I am also going to turn off the anti aliasing feature of the slicer as that could be aggravating the problem as it may produce grey scale pixels instead of just on or off resulting in partially cured resin. The resin itself is great though, maybe a little more brittle than the pigmented ones, but very tough.Grey resin is great stuff. As you can see from the photo, it holds detail very nicely. I don't notice any smell.The clear red came out pretty nice, quite clear, nice ruby red.The flesh is a good flesh color, looks good.White was a little odd, it came out looking nice and white, but when I put it under a UV light for a final cure it turned a light tan. Maybe not clean enough, but I won't be final curing any more white.

This is my current go-to resin for most prints. I prefer the Grey, as it shows details fairly well, but I've used the other colors with the same results. Once I got got my printer dialed in for this resin, I've had dozens of build plates printed without a single failure. It's really good.Prints with this resin tend to be very highly detailed and reasonable strong. In smaller pieces, there is some brittleness, especially if you overcure, so I definitely try not to do that. It is very temperature sensitive, and I try to make sure my printing room is 80 degrees F for the best results. I clean with a 99 percent IPA solution, using a dirty and a clean wash, and this seems to do quite well with this resin.Most recently I have taken to mixing in 80% Elegoo ABS with 20% Siraya Tenacious - for any prints that I want to be extra durable, or have extra fine breakable parts. This does seem to bump up the durability, at a slight cost of detail, but with this mix most parts I can drop from my head to the floor without any breakage at all.At the price point it's currently at (1kg for $40), this is a very competitive and high quality resin.

This is some good resin. I haven't strayed far from the brand that my printer (Nova3D Elfin2) came with, but I wasn't happy with their white. As shown in the photos after curing Nova3D's white turns almost a sepia color... if you will? This ELEGOO ABS-Like Rapid Resin stays white or at least a better shade of white.I posted a photo of an octopus, it's the test file that comes with my printer, that guy has sat outside for a few weeks at this point. Still just as white as ever. In the other photo, I printed some wall mounting brackets for my Bose SoundTouch monitor speakers. On the left is the Nova3D Resin and on the right is the ElEGOO ABS-Like.This stuff is great for printing lithophanes. It's successfully printed up to .1mm layer height (for faster printing).The Bose Bracket and the Octopus are both printed at .035mm layer height. Honestly unless you're looking and not-post processing, 99% of the things I print in resin now can be printed at .1mm layer height. A layer of paint covers up almost any layer marks, plus this stuff is strong.I will have to post a question to the maker.. I'm unable to dial in the perfect first layer settings.... Everything I try this thing sticks to the build plate like it was supposed to be married to it. I end up breaking the model by trying to force it off. The only way I've come around this was just put supports on everything, even the base, but with the Nova3D Standard Resin I didn't have to do that, it comes off perfectly (with just a tad force).I have been using the clippers that come with my printer as a trick to get the model to lift up, then once it's given up a bit of the adhesion I use the spatula... anyone recommend a new way? I'm new to resin (5 months)

UPDATE: April 2024 - ABS Like Resin V2 (Gray): The V2 Gray resin is more of a blue gray color than a true gray. It is also slow like other Elegoo resins. On my old Anycubic Mono X, I had to up the exposure time 10 - 20% to get it to perform well. If I left it where I had it dialed in for Phrozen ABS Like, I had print failures. Mainly failure for the print to stay together at the supports - lots of separation.Viscosity - V2 ABS is more like Phrozen resin. It is quite good viscosity and not thick like snot like the original resin.Smell - Not horrible like the old one but not great. It is somewhere between that. Almost a stinky floral smell.Overall. Not bad, but you will need to up your exposure time 10 - 20%. I now have exposure at 2.5 up from the 2.12. Your mileage will vary. I have not tried the resin on my Elegoo Jupiter yet but I would expect to up the exposure time as well.--------------------------------------------------------------------------------------------------------------------OLD REVIEWAfter complaining about how the Elegoo Clear resin was basically unusable due to a formula change in 2021, Elegoo reached out and offered to supply me with another resin. Since I mainly use ABS type resins for durability (slightly improved durability), I chose their gray color.It arrived and I used it to print a new model I was developing. The resin is thicker and less viscous than the normal brand I use. However, it literally printed very well with no setting changes on my Anycubic MonoX.Overall, I will say that Elegoo makes good resins. However, their clear resin is to be avoided for now until they have a better formulation. Hope this helps.

I make statues for fun. I have tried many different resins. I found standard resin to break easily. I am a klutz. I have found that the Elegoo ABS Resin to be very strong and accurate. I have dropped things with no damage where standard resin would break. I have little issue piecing together large constructions. The picture above was printed, standing 18 inches tall. One pic is just the print, the other is a primer coat in black and a white zenetel to show shadows.

Works great in my new Mars 4 good detail strong parts and prints perfectly every time so far.

si logran comprarla a precio de promoción les va a encantar, es muy duradera, muy facil de manejar y muy versatil, el color verde es algo chillón pero con un buen tinte la arman, es muy flexible y a la vez resistente.

The media could not be loaded. o produto ressecou e criou uma camada, uma espécie de película de resina no VAT da minha impressora 3D. Estou tendo que comprar um novo VAT por causa disso.

ok

Su resistencia mecánica no es resaltable pero es de esperarse por que es para prototipado. La calidad de los acabados que deja son excelentes.

Bad finish and overall bad