AIDA 20 Amp GFCI Outlet, Self-Test Nightlight Electrical Outlet, Tamper-Resistant Receptacle with LED Indicator, Ground Fault Circuit Interrupters, Wall Plate Included, UL Listed (1 Pack, Matte White)

Straightforward installation, great instructions.

tl;drtook 5 minutes of work for a noob with a screwdriverplastic retention plate doesn't come with the small screwsbright night lightpossibly defective light sensor (night light runs 24/7)Full review:So the unboxing experience is straightforward - you get the outlet, the plastic retention plate, and the screwless cover that snaps onto said plate. Instructions come in English and Spanish.My first electrical installation of any kind - it was easy. Just turn off power, make sure there's no current, remove old outlet, undo wires, pop the wires in this outlet, and finally reaffix the outlet. The snap on plate does not come with the small screws for it, so you'll have to reuse your current ones. Finally, put on the cover.The test and reset buttons work properly. My only gripe is with the light sensor, it appears to be broken. It causes the nightlight to work during the day, which will cause the LED to burn out quicker.

UPDATE 10/13/23Gave this outlet an additional star (3 to a 4) because the seller reached out to me to try to make things right. The fact the seller reads the reviews and responds when there are issues is impressive. That alone deserves an additional star.ORIGINAL REVIEW:Got this to replace a gfci outlet that had a nightlight plugged in, but made the 2nd socket unusable. This looks good, but the light output is much less than what was replaced. Using this in a bathroom where I prefer not to turn on a light at night. With this, I have to turn on the vanity light as the light on the gfci is too dim otherwise. Other than helping to find the light switch, this does not do the job I need. The installation instructions for wiring the outlet are some of the best I've encountered. Easy to read and follow the diagrams. As good as these are, there are no instruction for installing the cover. Best I could figure out, you screw in the clear plastic back plate, then snap on the outer cover. Unfortunately, that leaves a 1/16 -1/8 inch gap all around the edge between the cover and the wall. Totally unacceptable! No matter how I tried to adjust the fixture or cover, I could never get it to lay flat against the wall. I ended up purchasing a standard cover that is attached by screws, and that worked perfectly. I wish they had included a conventional cover instead of the one they did that is not supposed to show the screws. Installation of the outlet was a nightmare. It is a dual type of installation where you can insert a straight wire into a slot in the back of the outlet, or the traditional way of wrapping the wire around the screws. I prefer the screw method as I find it is more secure in the long run. Unfortunately, this outlet has some bizarre screws. Instead of being tightened down, they are somehow loose and flop back and forth. To get the screw wrapped around it, you have to lay the outlet on its side and shake it to allow the screw to drop down and give you room to wrap it. However, the screw is still loose in the shaft and constantly wants to push back into the outlet. I missed being able to loosen the screw and have it stay in position until I wanted to tighten it. After spending large amounts of time getting the wires wrapped around the screws, I was able to tighten the screws down on the wires to hold them. For the life of me though, I could not get the ground screw loosened, and was forced to use the back insert method for that wire. I have no idea how those screws are mounted. Strangest thing I have ever seen - screws that are loose in the socket, but are able to be tightened when a wire is present. Whatever they are, I hate it! Traditional screws please... Otherwise the outlet works as it should, but the dim light, difficulty in installation, and poor cover fit, would keep me from ordering this again.

I recently renovated a bathroom and I just could NOT leave the old outlets. This one is perfect. Clean, neat, easy to install, and the little light is quite powerful!

I installed this in a bathroom as a nightlight and it works great.

Not happy with these outlets. All but 2 worked. Went and got the more expensive leviton brand and they worked perfect. I have an outlet tester and know they were not wired wrong. Don't waste your time.

Chosen due to its black color and built-in night light. Overall good unit. The light is bright enough to light up half the bath so that you can use the sink, but not bright enough to bother outside the bathroom.

While this GFCI 20A outlet functions great as a GFCI, the nightlight feature almost never goes off. With a sunny day the nightlight remains on. I suspect this will impact the life of the nightlight. I did reach out to the manufacturer and after sending the requested video no further contact from them. Thus I am unaware of any adjustment that is available and therefore only 3 stars.