Preciva Crimping Tool AWG26-18, Ratchet Crimper Plier 0.1-1.0mm², JST Crimp Toolkit for 2.54mm 3.96mm, KF2510 etc. Connector, ATX, EPS, PCIE, SATA

Preciva Crimping Tool Kit with all needed materials.The tool, JST-XH Connectors and Dupont Connectors.Within a few days after ordering with Amazon UK I received this very complete set in France. The box it came in was well packaged with enough extra paper to make sure the kit itself was undamaged after the journey overseas. In the sturdy cardboard box we find the Crimping Tool, a very complete and helpful User Manual describing the ins and outs of this set in great detail and in 6 languages.It also comes with a lot of materials to crimp. Two boxes for transport safety packaged in a strong sleeve. One of the 2 plastic organising boxes (the bigger of the 2), contains 1550 Dupont Connector parts. They range from the smallest 1 pin plastic holders to the 6-pin wide plugs. With the small metal pieces for male and female connectors this makes up for a complete crimping solution. But there is even a lot more in this box as well. There are the elbow connectors (they will take a Dupont plug) that can be soldered to your pcb or experiment board. As well as a 150 cm 10-wire ribbon cable to build your first sets of cables with plugs from.The smaller of the two plastic organising boxes contains the 460 pieces for the JST-XH Connectors. This is a system where the male part is soldered to your board and the cable is crimped to the plugs. It delivers plugs/connector combinations from 2 up to and including 6 plugs. The box itself is of a different make compared to the bigger box and might be a little less sturdy. So far it works very well for me.After these preliminaries lets see how the crimping works. The crimping equipment is very sturdy with a good grip. It has a ratchet that blocks the tool in a few steps which turns out to be a real help when crimping. After reading the manual that is very detailed and easy to understand I made my first set of cables with plugs. The way to do this turns out to be very easy if you set the tool with 2 clicks from the wide-open setting. Then you can feed the small metal pin in one of the three openings (see the manual). The numbers 1-3 should be turned towards you (visible) when you feed the pins into the beak. Then you need to visually check how far to feed the cable into it and finalize the crimping movement slowly but surely. At the end of this movement the tool can again be opened and you should have a well crimped connection.All in all I am very pleased with this new addition to my electronics workshop. I have used it in a variety of projects connecting separate electronics circuits on pcb's to each other and for making connections to various sensors and other modules like GPS or break-out boards. The pitch is 2,54 mm which is the standard for most of the experiment boards and solderless breadboards (see pictures). It gives you more than enough parts for many years of DIY-electronics projects. And the tool itself will outlive you if handled with care.I can heartily recommend this Crimping Tooling!PS. pictures of pcb and solderless breadboard showing some usage scenarios, these are not included!

I have used a wide variety of crimps and crimp tooling over the years from ultra-cheap pressed steel junk to industrial tooling costing hundreds of pounds. I have wanted something to manage this sort of crimp system for a while but I hadn't seen anything I could afford. When I saw these and that they came with terminals my expectations were pretty low to be frank but I have been surprised by just how good they have turned out to be.The quality of the frame is high, with well formed and aligned steel pressings that appear to be properly riveted together. The hand grips are comfortable and well attached to the frame. The all important jaws set is well machined, seems to be properly hardened and meshes very well without any obvious lateral play or interference.The crimping action itself is smooth and positive without frame deflection, though you wouldn't really expect any with crimps this small. My only niggle is the practical difficulty with setting up and aligning the crimps themselves while ensuring correct placement of the wires. This is not really the fault of the tool but the consequence of having to hand crimp such small parts. The resulting crimps are perfectly formed and secure. I have tried a couple of manual pull tests and the crimps seems as well formed as any I have done on manufacturer supplied professional equipment.I haven't tried all the connector permutations but the first lot are going onto an Arduino Proto board so that should show up any quality issues with the actual terminals themselves but so far I am delighted with the tool. This looks to be a positive addition to my toolbox and represents almost unbelievable value for money.

This is a relatively cheap kit, with a wide range of connectors.The crimp tool is very good (much better at wrapping the cable grip prongs than my previous one).The range of connector shells is pretty good, but is missing double row versions.But: For the price it covers a wide range of options, and works well.

The tool has correctly a shaped jaw for the round dupont terminals's insulation clamp, and 2 sizes of jaw for other types. The supplied dupont terminals are better quality than the ones I have bought separately in the past. I have never used JST terminals before and wanted to try them, so this was a good include for me. They fit the end position.The ribbon cable in the kit has very fine non-plated conductors. I don't know the gauge. Something around 0.1mm^2 I think. It's actually described as IDC cable in the product description, which would appear correct. I was able to strip the ends for my test crimps using my thumbnail.Test crimps on the supplied cable with a pair of each type of terminal very satisfactory, was able to get correct position with no problem, worked correctly first time. Absolutely no messing about, no adjusting post-crimp, no having to straighten the terminal. Fantastic.The tool is more expensive than similar looking tools you can buy elsewhere, but definitely worth it for the peace of mind knowing you're getting something that works, and the value-add of the included terminals and cable is reasonably good.I wouldn't go so far as to say the produced crimps are 100% as they do have flaws. You only get 100% with a professional tool costing 100's of pounds and it is not a fair comparison. As an amateur tool however, it is excellent.

perfect

Parfait pour sertir les connecteurs JST 2,5mm. Bonne qualité du sertissage.

Easy to use, and makes good crimps.

La pinza è costruita bene e i materiali ottimi.Usata per connettore XH 2.54 mm e ha svolto egregiamente il compito.Impugnatura comoda.Per uso hobbistico perfetta

Come descrizione