eMylo® AC 220V-230V-240V 1000W 1 Channel RF Wireless Relay Remote Control Switch Transmitter with Receiver

Very good value.The way the unit behaves on remote button press can easily be changed via a pres-button on the board.I found the range a bit limited initially, it wouldn't trigger when the fob was indoors and the receiver in the garage, a separate building. I found that uncoiling the antenna wire and leaving it dangling increased the range significantly and it then worked reliably.The relay contacts are 'volt free' so you can connect them anywhere you'd have a switch. You could use it to power house lights if you wire it such that the COM and NO contacts replace the switch, and L and N supply mains power to the receiver. Simple enough to do, but of course if you're not confident get somebody who knows their stuff to do it, mains can kill!I did find that the housing it's supplied in is a bit curious, it prevents access to the relay terminals. Bizarre... I had to cut a slot in one end so I could get the wires in.Bear in mind that the device needs to be installed within another box since the connector strip allows contact with live mains.Overall, highly recommended.

For the money worked great for the project I needed them for, instructions are a little confusing and the live and neutral are different on the pcb to the instructions so check before putting any power. Worked fine on UK Mains power (these are the mains ones not dc powered). Found that I had to get closer than I would have liked to use the remote but was OK for the job I needed them for

Great piece of kit. Easy to install once you figure out the wiring. The diagram is t too clear. For anyone not sure, 1 is both neutrals (Blue) 2 is live incoming (red) 3 is live switched (yellow) and 2 & 4 should be looped to each other. You will also need if using outdoors a clear lid IP66 housing large enough to take all of your wiring. If using a solid plastic lid, I found it weakens the RF signal. They work great on all my outside lights which I have rigged up on 4 separate circuits. Going to buy more for friends Christmas gifts. Any questions please ask.

Excellent product. Used these to operate garden lighting and for a battery charging station in my shed. No longer have to walk down to the shed in my slippers at night to turn off the chargers and have avoided the need for a ton of cabling for the lights. Range is quite good - although mine suffer a little as they're amongst wiring which are shielding them a bit. When first tested (i.e. away from other wiring) they operated in my shed (about 25 feet away) through three lots of glazing. They still do, but it takes a few clicks at times. As the relays are quite small, I used an additional heavier relay for anything that drew a bit more than a light, although they are rated at 10 amps (if memory serves).

Seems to be working as intended, but not being proficient with electronics I had a tough time figuring how to connect this thing, even though the manual was provided.So here's the deal: IN+ and IN- are for powering the device. You plug the hot wire into one and the neutral wire into the other. Doesn't matter which to which, as long as they are not the same wires. Then you need to connect either neutral or hot to the COM (Common) pin. I recommend the hot wire if you're sure what you're doing - otherwise try with neutral. Then if the relay is off it will transfer the current from COM to NC (Normally Closed), but if you switch the relay using remote it will transfer the current to NO (Normally Open). If the hotwire is connected to COM, the connect NO to the hot wire of whatever you'll trying to power, and the neutral wire from your power source to the neutral wire of whatever you'll trying to power.You can bridge the IN+ with COM using a wire.

Works really well. I control from the house to the garden shed which is some 10 meters away. The remote is a pleasure to use. The information provided about wiring the remote is confusing. You need to take the top off the controller, then look at the connections which are labelled. The 2 on the right are for power (as per the information), then the next 3 are the relay .Overall, really impressed.

What can I say, a superb piece of kit. Programmed in less than three minutes, installed in 10 minutes. Yes it does need a dedicated neutral feed but that didn't cause me an issue as i always run 3 core to all switches (as a just in case ) I would have given five stars but there seems to be a coding anomaly when in mode 3 . I set up two units - unit 1 (jog - to activate a door opener) - on - remote A ( Push - release ) - unit 2 ( toggle - hall lights ) - on remote c -off - remote d - this worked ok, however - when 2 was on and and 1 was triggered - 2 went off ??.I tried all combinations of button configuration but couldn't get this to work correctly.This was finally overcome by switching unit 2 to latched mode, which was a bit of a pain , as i really wanted a dedicated "off" button.I'm running a Broadlink system and all 4 devices programmed seamlessly into this , so effectively I've got 4 remote / wifi/ 4g integrated switches for the price of 1 Wallpad Rf light switch ( I now have a spare remote too )I bought these Thursday - delivered Friday ( Thank you Prime ) - and I'm ordering another 4 Monday ( Let's hope they're not on the same channels )

Easy to wire up. Screw terminals seem to be robust. I wired three of them up to my outdoor pir sensors so that I can turn the power off to the lights totally if I want. I mounted it on an outside wall inside a waterproof sqare box. I still have three spare units so I think I'll connect up an led floodlight at some point.

Sencillo y útil, tenía un receptor que no podía acoplar mando y me ha servido genial y económico

Top Qulität

Einfach nur Gut, ok wir haben sie jetzt zeit einer woche im Einsatz und schalten Täglich 15 mal. wie die Lebensdauer ist kann ich nicht sagen aber bis jetzt begeisterung.Einfache Montage, eingache Installation kleine aber nicht zu kleine Bauform einfach mal ein gutes nit billiges Produckt. Preis Leistung perfeckt. War bestimmt nicht das letzte Set das wir gekauft haben

Das ist eine Top Produkt ich kann nur empfählen

Der Empfänger ist super verarbeitet und funktioniert perfekt. Die Leitungseinführung muss allerdings mit einem Cutter etwas angepasst werden. Ich habe 2 Artikel gekauft und bei beiden war es gleich (leichter Konstruktionsfehler, aber damit kann man für diesen Preis leben). Ich verwende ihn als Impuls für mein Garagentor. Die Programmierung der Funktion ist absolut easy.Die Antenne muss man aus dem Gehäuse heraus führen damit der Empfang besser wird.Der Empfänger funktioniert durch 2 Hauswände und steuert problemlos das externe Garagentor.Die Sender sind ebenfalls top verarbeitet. Das schöne ist, man erhält 2 Sender. Absolute Kaufempfehlung.