ZIRO PLA Filament 1.75mm, 3D Printer Filament PLA PRO Basic Color Series 1.75MM 1kg (2.2lbs), Dimensional Accuracy +/- 0.03mm, Black

I had a large print to run (4 days). I have had issues in the past where the print had to be abandoned due to filament issues.Using this filament it ran through non stop without any problems whatsoever. Stuck to the bed like glue and produced a really high quality finish. Have already ordered some more!

This is the try third type of Ziro filament I’ve bought, the other two being high speed white and mystical green. Each one has been perfect. The winding is neat and am yet to have a tangle. The print quality is spot on and the value for money is the icing on the cake. Would 100% recommend

I've used around half of this spool and so far it has produced reasonable results. I get a bit of stringing between point on the print but i havent tried to tune these out yet. I suspect a bit more retraction will sort it on my Anycubic Predator. The print quality otherwise is good, with a nice glossy finish. Bed adhesion on the ultrabase has been consistent. On the whole, I'd buy another reel and I'll see if I can tune out the stringing or use my Anet which has a direct drive extruder and hardly ever suffers this problem. I've dropped this a star since my last review as I bought a roll of Yellow PLA of the same brand and it's been a bit disappointing. The colour is very washed out compared to the Esun filament previously used and it's not sticking to the bed where the finer detail is, such as small holes and sharp corners. Maybe I've got a duff roll because the blue seemed ok and was a vibrant colour. It's like I got a Friday afternoon roll, just before they turned out the factory lights for the weekend.

Ziro is one of those filament makers that has batches of good and bad filament.i've had filament from them that was horrible to use, acting as if it was wet, but after drying repeatedly it would not stick or print well.This reel of filament has been a pleasure to use, sticks to the PEI sheet well, good quality prints.. but i do use a prusa printer, so that is part of the equation.It's a lovely shade of blue,

Ziro filament has been the backbone to my business for three years now. I always use it for my products ( Ant nests) and have found it to be the most consistent and nicest printing filament for the job. Even on Bambu printers at their high speeds it prints well! I can recommend to anyone. The included filament sample + cleaning filament is always nice, and getting a bag to store it is a great bonus too.

Using at 220c hot end and 70c bed on Ender 5 pro, with sugar coated Borosilicate glass (see YouTube if you don't know what that's all about). Sticks to the bed really well during printing (really well!) and just pops off by itself when it cools to 38c with no effort at all (you hear a pop and then lift your print off with 2 fingers). The quality of the prints are spot on, with the standard benchy boat not having a single sign of stringing/sagging or any blemishes, a perfect print! If you get any under extrusion/head clogging firstly back the tension right off on your feeder and leave it there as this filament does not like high tension as the gears leave indent marks in the filament and causes it to grip in the bowden tube (even upgraded tube). If you have blobs in your prints (pimples) go to your slicer (I use Cura) and find 'mesh fixes' turn the maximum resolution to 0.5mm, maximum travel resolution to 0.5mm and maximum deviation to 0.025mm, that will cure it. I just purchased many more rolls of this filament as I am now getting through at least a roll every week as this is now my 'go-to' reliable filament...

So far has given excellent results for my new high speed 3d printer

Filaments a little more transparent than I’d like / expect from orange stuff but can’t complain about anything else

Easy to print and great fluorescent green color.

There is so much to say about this filament nothing but fantastic A+++.I recommend this to anyone, it's wound nicely and comes with extras in the box. Will be ordering this all the time

The media could not be loaded.  I absolutely love the colors. I need a shade of pink but unfortunately, this pink is not the pink that I actually need it for a project that I’m going to use. I love the fact that it comes with a sample of printer cleaner, and also a sample of filament. The seller is amazing and it looks like the product would be amazing if it was what I was actually looking for. I know it can be hard to gauge the actual colors because pictures and monitors are different. Again, the pink is beautiful it’s just not the shade of pink that I’m looking for at the moment. I also love that it comes with a storage pouch.

Did a manual filament swap on a Voron cube so you don’t have to. All these colors are working fine for me. Love the back light possibilities. Reasonable price. Smooth print at 210/65-60.Will be my go-to for clear filament.

Bonito color. Tuve que subir el calor de la cama porque no me quería adherirse. Pero luego todo bien.