ELEGOO 6PCS 170 tie-points Mini Breadboard kit for Arduino Project 6 color Breadboards Mini for Electronic Kits UNO R3 MEGA NANO…

Elegoo electronics are usually good quality and the breadboard are no exception. Excellent breadboard, good strong material and good spring connections with clear row and column markings. The rear is good self adhesive. Elegoo support is always good. So all in all a quality product at a reasonable price.

These are so much better than the rubbish ones I bought from another website. The print is bold and clear so they look better but the best bit is how they hold components. Even 1/4W resistors and small caps are held tight and don't feel like they'll fall out while placing other components. These are well worth the extra few pennies that cost.

Purchased BB830-equivalent from a couple of providers. ELEGOO’s one has very good plastic quality and manufacturing: breadboards are flat, pin holes accurate and markings easy to read. Regrettably, contacts are not consistent across the board; some are tight (easy to fix), some other are too loose for 22 AWG wire. It would have been 5 stars otherwise. Breadboards come singularly packaged. Very nice, although I’d personally trade this in for more accurate contact clips. Definitely recommended for amateur, educational or any project for which very high reliability is not required: in these cases it’s great value for money

An old fitter once told me, “when it comes to tools, you buy cheap, you buy twice.” And that’s something that’s stuck with me because every time I try to work in a budget, something invariably goes wrong and breadboards are no exception. I’ve had a few over the years but this is my first Elegoo - an Amazon recommendation. I’m working on a couple of Arduino (clone) projects at the moment and a breadboard is the way to get things working in a hurry - or at least, it should be. The problem (with the cheap ones) is this — the sockets are stiff and often have unreliable connections. This results in two things:(a) a lot of loud cussing because the fine leads on components like small resistors, jump leads and many other small components bend as I try to push them in. This can be exceptionally frustrating. (b) worse, when the connection fails, so does the circuit, but then it can be anything from tricky to a virtual impossibility to figure out what is wrong: is my design off somewhere or have I put a lead in the wrong hole? Finding it’s nothing more than a failed socket is enough to bring tears to your eyes when you’re up half the night trying to find the fault which was no fault of your own. Other than trying to save a few quid on a BBB - a Bargain Basement Breadboard. And yes (a) has happened recently and it was fortuitous that Amazon recommended these and our of desperation, not to mention sore pinkies from fiddling with overly stiff sockets, I took a punt. When they arrived they looked just like every other breadboard I’ve had - that was until I tried to put a clone Arduino in there and oh boy, those sockets felt tough. My heart sank a little but it’s new, so I figured they’re just a little tight and breadboards are not ideal for such large pins, particularly when you’re trying to put 30+ in at one press! Then came the acid test. How hard is it going to be to mount a discrete component in there. First off, I tried an LED. In she slipped, buttery smooth and fitted like a glove. Perfect fit, both leads, first time with very little effort. Nice. Now some Dupont pins (Elegoo also available on Amazon) and in they went - first time, smooth and with very little effort. 1/4w precision resistor - with fairly delicate leads? Dropped in like a champ.Very occasionally I did find that some holes were a little tight but that’s more about my lazy attempts at not centering the component before trying to insert it. Compared to the BBB this was like going from a 1* B&B to a 5* hotel! It was only at this point that I noted another (small) but interesting departure from my other BBB... the power rails feature slightly larger sockets. Again this sounds like a “so what?” but you can tell some thought went into this as the power, ground in particular on audio circuits and many digital designs, carries a fair amount of current and larger pins means lower resistance which means less hassle. Sweet! I’m starting to fall in love with this. For larger designs, most breadboards can be connected and this one is no different, but careful attention to tolerances has ensured that it’s possible to stretch fairly large HATs (Hard Attached on Top) across more than one board. Considering the tolerances involved this is quite a feat and I’m grateful for both the locking mechanism and the very sticky pad which held tight to the surface of a scrap piece of “hardwood” flooring. It will take longer to determine how robust these boards are but my initial impression is that they are built to last and should give a long service life. Unlike, it has to be said, my BBB which I’ll be donating to one of the apprentices just to tease them. :) Photos show the slightly larger power strips and a BBB with an Arduino clone vs. the Elegoo hosting another Arduino with an AZDelivery resistive touch screen (available on Amazon for the Uno).

these are the breadboards I have been dreaming about. I am building the Ben Eater 8-bit CPU and have had an awful time with inferior BBs. everything about these is fantastic, they are stiff and strong, they hold through hole components, or jumper leads with the exactly correct amount of physical resistance. if you want to know how to avoid rubbish boards, and see the general quality which goes into the manufacture of these boards look at my pics. firstly these are not only in a a big box, each board is itself individually boxed. no company interested in selling junk to make a quick buck would use such expensive packaging. in my second picture a cheap board, which is full of components, is positioned next to an elegoo board. look at the contrast in colours. the cheap board is white-ish and fairly transparent. whereas the genuine elegoo is a much brighter white, and is completely opaque. if you care at all about the quality of breadboards these are the lads to get.

Perfect breadboards for prototyping my project Pins seem to grip well in the holes cannot fault so far

Great, for components, hard to use with 24awg solid core wire - too much resistance for such thickness. Very cheap though a

Very good value for money, super fast delivery, product as expected and in good condition!

Super

Les breadboards sont de qualité correcte. Les pads adhésifs à l’arrière gênent l’emboîtement ou le retrait des barrettes. Fonctionnels, mais pas très modulables.

Un set di basette di buona qualita' ad un buon prezzo

كمبتدئ يمكن تشتريه وتحسبه بالحجم الكبير، بس انتبه، ترى الحجم صغير

صدمني حجم البورد بالبداية بس يعني يؤدي اللي تتوقعه منه