60 Inch LED Tailgate Light Bar with Reverse & Sequential Turn Signals for Truck

Tailgate Light Bar is bright, works great and it is Easy to Install There's plenty of wire to to reach the plug and to wire in the brake light. A good thing to know is you have to wire in the back up light wire. But that's easy just undo the tail light on vehicle and find back up wire on it and wire it in .

I added these to the back of our camper. Original lights are small and get hidden behind bikes. Ran these up the camper on both sides. Tied in to original light and worked perfectly.

Don't waist your money and time. It's cheap junk. You get what you pay for!!! I plugged it in before installing. Everything worked and the LED's looked really good. Took my time to do a detailed job of cleaning under the tailgate then sticking it on. I even rolled it out the day before so it would be flat and smooth. The adhesive wasn't very good and I don't think it would have stayed in place very long. After installing, I checked all the functions of the LED's. I noticed it wasn't working like it did the first time I plugged it in. Checked the four pin plug and everything was fine. Each time I tried it I noticed the LED's were doing weird things. Some were working, but not going all the way to the edges of the bar. I gave up on it until the following day. I tried it again and it was even worse with the LED's going bonkers flashing on and off with no consistency. This thing is so cheapy made it's mind blowing. The four pin plug and wiring are so thin. I never should have ordered it knowing this would probably happen. I've already boxed it back up and printed the return label as a defective item and will be taking it to my local UPS drop off tomorrow morning. I will be buying a quality "American Made" LED bar soon. Yes, it will cost me more, but it will work properly and last!!!

Love these lights! I just need to extend the wiring harness so that I may hide them from view and make it look like a more professional installation!

So far the LED light bar is nice and bright and I’m happy with its functions and looks. There are two drawback the wire cable could be another foot longer. AND the other thing is the thickness of each wire very thin, like maybe 20 gauge wire. Plus they are not wrapped for protection. One other thing, due to the led thickness, it’s hard to place behind the bumper on a 2023 Rebel. Had to actually mount on top edge of the bumper.

I was a little hesitant in setting my expectations due to past reviews of other users on here, BUT, I have to say that my experience has been different from the individuals with less than stellar experiences. First off, let me say that in addition to the included instructions, it's worth mentioning that you should look up a couple YouTube videos on how to properly mount these LED brake light strips. The first thing I did was to lay out the strip on my workbench table for 48 hours in a semi climate controlled garage. I placed 2 pound weights on the ends to keep it stretched for the two days. Then I used a heat gun to apply low heat to soften the rubber surrounding the stip prior to application. (Apply heat only on the backside and not the front side where the LEDs are located). The MOST IMPORTANT thing to remember is to thoroughly clean the surface where you are mounting the LED light strip. I used original Simple Green cleaner in a spray bottle with a clean lint free microfiber cloth to wipe down the surface three times with about 5 minutes between each clean to facilitate the surface drying. I then took large cotton balls and doused them with rubbing alcohol and cleaned the surface twice, again, with 5 minutes between each application to facilitate drying. I then waited 5 minutes and used my heat gun on low to ensure the surface was completely dried of all moisture and to wqarm the surface a bit, then began the application of the light strip starting from the left side of my truck to the right, ensuring even application so as not to get the wavy light look (LOL!). Made my connections behind the rear bumper and tested for functionality. The light strip works perfect and having the reverse white lights is really cool. I've had this mounted for about a month now with no issues whatsoever. The adhesive is STUCK to my truck. I even tried pulling it off and it just stuck. Would not budge. Lights are bright and work perfectly with no LED's burning out even afte about half a dozen car washes with a pressure washer. I highly recommend these lights.

Light bar quality is good.. fits perfectly and looks great

Whoever wrote the program for the microcontroller does not understand the signals on a 4 wire trailer harness. When you step on the brakes, initially the yellow strip will come on and then switch to intense red. The yellow should not come on at all. When braking and using a turn signal simultaneously, things really get funky. The correct direction flashes in sequence as it should, but the opposite half of the yellow strip also flashes. This is very unclear signaling and liable to get you pulled over. The LEDs themselves are sufficiently bright, but the wiring is cheap and should be a studier gauge. Don't buy this crap. See the attached video for the issues I described. Note the flickering you see in the video is due to the camera and your eye won't see that. Also the dark spots you see towards the edges are due to my installation (those LEDs are blocked by a bolt). UPDATE: The seller reached out and offered me a full refund, which I accepted. They say that there is definitely something wrong with the strip I have. Nice that they did this without asking me to return it as it's fastened in place and not easily removed.