Sheffield Bronze1454 Porcelain Filler/Repair, 1 Fl Oz (Pack of 1)

Product works great. Easy to apply, easy to sand. Comes out looking great. It’s very runny so it takes some work on a vertical surface. I removed a shower door assembly so I could use curtains. The holes left by the screws also left some cracks in the porcelain as you can see in the pictures. Because it’s so thin and runny, I had to apply several coats to fill in the holes. Hindsight, I should have plugged the holes with something to give the liquid something to set on. Either way, the result is good. I still have to use the Sheffield touch up paint which I will also review after the job is finished. Very satisfied with the results of this product.

We used this to repair our washing machine tub that is pretty old and has some chips in it. We prepped the surface by cleaning it and then wiping it with rubbing alcohol. My husband applied it in several thin layers over the course of a day and we didn't use it for a few days afterwards so it would have time to be fully dry. I've since run several loads of laundry and it's holding up fine. We did the bathtub the day before we left for a 3 day weekend away so it would have a long time to set as well. Same prep and application as the washer. That one is lasting well too. It's slightly off white, not glowing bright white, which matched the tub well and barely shows if you don't know what you're looking for.

It is okay. I have used porcifix in the past, which is a bit better in my opinion, as it cures faster, and can be easily sanded to be completely smooth and shiny. I also remember it being easier to apply to fill in deep pits. This product remained tacky for a long time, even when applied in small layers. It did not change much while curing, leaving brush marks and a rough texture. It also is not very hard when cured, so sanding around the edges caused it to crumble a little. Over time I will know how it wears.. my previous patch jobs with porcifix lasted years and remained shiny after being sanded with very fine paper.This off white color is not going to match coatings that are your typical brilliant white, but it looks OK. None of these give a perfect match anyway.

Sheffield Bronze 1454 Porcelain Filler/RepairYea.....Unfortunately, I am in the 10% who have the displeasure of giving this product a bad review.I researched porcelain repair kits, and looked at the reviews of them, and this seemed like a good product...I have the same problem as others...It will not cure. I am not an amateur DIY'r, and followed the directions VERY carefully.No water was in the shower for 3 weeks prior, as I was painting the room, replacing some plumbing, and the stall was cleaned well.Product was shaken EXTREMELY WELL multiple times....(just to be sure it was mixed)I applied the several coats of the filler 2-3 hours apart and checked it 12 hours later, and it was like putty....So I waited another 24 hours for it to harden into a "ceramic like" filler.I just tried again (72 hours from the last application) to sand it.... and it was like sanding plumbers putty or caulking.Even though I did not buy it directly from Sheffield Bronze, I just contacted the company.While the operator was cordial, the response was, that I must have applied it too heavy, and it must have trapped moisture.They suggested removing it all (which since it is still in a "putty-like state", shouldn't be hard), and reapplying the filler.....Re-Applying it in very even, very light coats,..... and said I could speak to someone else if it fails again.....uuughFYI: This was being used on a shower stall at the radius in the bottom where the wall meets the floor. (small pitted areas)I have been coating,waiting,trying to sand, and messing with this for over a week now.I will try it again...But i am not feeling very "warm & fuzzy."Apparently it worked well for some, maybe you'll get lucky too....IDK.If can manage any better results, I will update my review.....But I am very doubtful at this point.***22 hours Later-(3) SUPER light coats applied, 3 hours apart-It hasn't cured and my review is unchanged***This product may work on a surface blemish or crack that has no depth...IDKThe product has the consistency of paint ,so filling a spot that has any depth( .25-2mm ) will take you many hours, many coats, and quite possibly won't cure even after spending that much time.

At first the color was just right. It is definitely an off white color with a ivory undertone to it. It was great at first but after a month it became more of a yellow ivory than white

I have a white enamel-over-steel sink. It had about a 1/4 inch ring of chips and rust around one of the holes that was coming out around the faucet cover plate. I used a dremel to takes off all the rust and clean it all up, then used the porcelain filler and repair in 2 layers to get an even layer. Let it dry for 1 1/2 days, then put 2 layers of the Sheffield porcelain touch-up over it and then remounted the faucet cover plate and faucet. Works absolutely wonderful. The Filler is a beige in color, and the touch-up is white. It's a bit whiter than the rest of the sink, but I can live with that. At least my sink is well protected now, and this will hold until I win the lottery and can build a new kitchen... Very happy and satisfied..