Audio Innovate Mini InnoFader Plus Non-Contact Crossfader

I got this crossfader to replace the stock fader in my DDJ-SX2. The SX2 crossfader is decent, but it felt like it wasn't very smooth and I knew there had to be something better out there. I read up on this fader, and it seemed like people were liking it so I picked one up. I can say it's a lot better than the stock fader on the SX2. It feels smoother and makes for much tighter cuts. The SX2 is one of the Pioneer controllers where it's very easy to replace the crossfader. Just remove a few screws right near the fader and swap it out. I would suggest when you put the Innofader in, to put 2-3 washers that come with it on each screw so that the fader cap doesn't sit too high. The fader cap feels really nice in my fingers as well. I was doing transformer and crab scratches with no issue using this fader. The movement is buttery smooth. Make sure to put a bit of the Deoxit fader lube onto the fader rail when you install it. I give this crossfader 5 stars across the board. I'm very glad I decided to get it, and it's going to make my journey to become a master scratch artist that much better. Peace in the Middle East!

This is an amazing fader. Small compact and easy to install. Our use this in my pioneer DDJ SX2 as a last minute replacement. Pioneer is out Of stock replacement faders and everyone else who has them in stock would not arrive in time. This was a simple replacement, The hardest part was figuring out which jumper to use. You will need to use the factory bracket when installing in the pioneer DDJSX2 controller. And don’t forget to flip the switch on the back of the fader before reinstalling. The fader Provided very smooth and precise cross fades and it feels very nice and quick jabs and scratches. I am primarily a club and house DJ and this replacement works just fine. If you are a hip-hop scratch DJ you will be even happier. If you were looking to upgrade to a new feeder then this is exactly what you need to get. Don’t waste money on the factory replacement that would cost roughly the same amount of money and could take weeks to become available. I will be recommending this product to anyone who asks about it. I’ve been DJ in for over 25 years.

Everything was fine until I got the oil package leaked inside the box.

This was exactly what I needed to replace my fader on my DDJ SX2. Came with fader and various alternate cables for simple hook up. Instructions were clear and the final product came out perfect. My cuts are very precise. Would definitely recommend.

I was not sure i wanted to do it. I was thinking about sending it to a shop . I'm so glad i did it myself it only took 35 mins i was ready to play music. great feel great sound. i will tell my friends to use this when they ready to change it on there set.

The Mini Innofader is a very very good replacement for most controllers and mixers that come with stock crossfaders its small size will fit into the tightes of mixer n controller spaces and gives you the professional type fader feel and cuts that pro-grade mixer's have ..you can also manually Ajust Cut -in times and fader Curves to your likeness., its very smooth and will take a few tries to get use to the feel of it. if your upgrading this is the perfect replacement and a Quality Product..

Ehhh... Installed it for my Pioneer DDJ-SX initially and it was okay. Installation and calibration were a bit too much. Once I connected it. Had to do a test run for about an hour or so, just to get this scratchy/clicky noise noise coming out when I was scratching. Installed into the Akai AMX mixer as shown in the picture. The mixer itself had the Innofader Duo already in it and that was the first time I’ve ever used an Innofader. The cut wasn’t sharp at all even after calibration. So with this fader installed, I thought it would be better since a lot of DJs recommended Innofader’s, but cut is still not that sharp even after calibration and you see the “Xfade Curve” is on full cut. Wouldn’t really recommend this product to anyone. Maybe if they came with “spacers” for each side of the fader it’ll help. Other than that, just gotta wait until Jesse Dean makes a universal contactless fader that you can slap into any mixer.

This fader is the perfect fir for my denon mk|| controller...recently the factory fader went bad with a lot of static went moving it from left to right,so a friend suggested this one as a replacement and it works Great! Thank's guy's,and the next day pickup made things so convenient👍🏽

This is an awesome crossfader, easy to install , very clear instructions. If you’ve got a mixer that still using carbon or plastic contact tacks, this is a must have fader. This fader is unbelievable for scratching, cutting and mixing. I love the fact that you can tune the cut in point. This fader hands down beats any other crossfader on the market, trust me!

Il prodotto è ottimo. Consiglio di non fare nessun settaggio. Basta selezionare il cavo tra quelli disponibili, collegare con il mixer e posizionare il commutatore verso l'alto. In questo modo la curva è regolabile dal mixer. Il taglio standard risultera' abbastanza buono, con un sufficiente equilibrio tra curva e cut-in. La confezione include cavetti, viti e piastre metalliche per adattarlo ai diversi modelli di mixer. Ottima qualità. Consigliato

A bit over priced for third party amazon reselling. Would have preferred to have gone direct. But the product is great! I knew that going in.

ok

En remplacement du crossfader d'origine, installé sur un contrôleur Numark NS6 2. Le mini innofader est un révolution, les coupures sont nettes et précises, rien a voir avec celui d'origine. En plus, il est compatible avec beaucoup de matériel.