Tekno RC6852x Rear M6 Drive Shafts/Hub Carrier

Love Love Love these CVDs!!! Tekno is one of the best companies I have ever had to deal with. This is one of those no brainers. These shafts routinely hold up to 4S power with no problems. The only thing I want to tell you is DO NO RUN RPM CONTROL ARMS!!! That is directly from Tekno. The RPM plastic is known to flex so much that they will bend the driveshafts. I run the stock arms and they are much better IMO. Very rare that I break one and if I do its becase I smashed into something. Don't get me wrong I love RPM, but NOT in this application. I had the RPM A-Arms on my STRC LCG Slash 4x4 race truck and i was always adjusting camber/toe it would seem after every race everything would change. I blame it on the very flexible material they use. Very good in some areas, but bad in others. Since going back to stock its perfect. These CVD's are designed in a way that captures the hinge pins, The rear carriers offer much more adjustment then stock, and they are super beefy I have NEVER broken one, nor have I even seen a broken rear Tekno carrier. Buy them already you will not regret it.

They are holding up well. They also send you some free Tekno stickers for your whip and extra caster blocks (?) in case you break the ones you get. I suppose there are slight differences in camber or toe for the extra blocks, however, when you are bashing, not sure if it matters ALL that much

Ok so. I have these on the rear if my stampede vxl. They are stronger and beefy. The problem is there is not the same amount of thread length like the stock ones have. So when there is not enough thread sticking thru for the nylock nuts to grab on to. As a result the wheels are constantly coming off. Also yes first blue locktight then red locktight. Still nuts come loose. If you are reading this techno rc. Just give them a few mm more thread length and that should be good.

Best drive shafts made. Just wish the rest of the parts weren't plastic. The plastic is wearing out and causing the wheels to wobble..... UPDATE... still have not broken anything running castle creations electronics 15t pinion, 54t spur and 3s all the time. But the plastic parts are wearing out pretty bad. The wheel wobble is pretty unbearable now.. And the pins inside the stubs are worn out allowing a lot of slop. But.... still not broken after almost a year.

Finally I found the right ones i finnaly just payed the extra few bucks or you will spend alot more in the long run. Horizon Hobby is the 1 stop Shop for all your RC needs unfortunately FedEx had a Hicup and there was a delay of a few days of no fault of there's so I can't hold Horizon responsible for something not in there control.  They shipped the order out the sameday 👍  They have a awesome selection Great deals 💸 and Fast shipping and the most important thing 👉 Great Customer Service

These things have served me perfectly. Worked for months with hard ripping and drifting in my slash 4x4 stock electronics. Motor dies, (yay for rust) these beat the replacement motor where the new replacement motor shaft ripped out of the car. I haven't had a single issue. It feels more responsive, whereas before it seemed like the crappy stock shafts were twisting as it accelled. I'm working on fixing it up now, still works after a half year in out florida garage. (using a brushed motor from a stampede) These will serve you well, please do not buy more of the Traxxas plastic shafts. They are absolute trash. I have a PILE of them with broken u-joints. These guys really made a quality product. I can't stress this enough, I am pissed at traxxas for providing these when they WILL break out of the box, with no power upgrades.

I was looking to buy axles for my slash 4x4 and couldn't decide on whether to get these, the MIP X duty or the upgraded traxxas axles. Based on other reviews from other products, I decided to go with these and I couldn't be happier.Installation was very simple and straight forward with the included instructions. I run on grass/dirt and asphalt. These hold up to 4S without skipping a beat. Sure you have to ditch the stock rear axle hubs but in my opinion these are a little bit stronger and give you more adjustability. I would buy these again in a heartbeat.

For referance I have both the Tekno and MIP X-duty driveshafts.I installed these on my Stampede 4x4 and I have to say that I really prefer these over the MIPs. I run my Stampede on 3s Lipos and have pushed it just as hard as on the MIPs and have yet to break them. The Teknos are considerably lighter and has less intricate parts. The reason i bought these and replaced my MIPs is because I was having issues with the MIPs coming apart while running the truck. The cross pins would slide out and the two halves of the shafts would separate. These cross pins come in a 4 pack and usually cost about $10 shipped I honestly have spent about $30 just on these cross pins until I bought these Tekno's. One draw back I can see is that these Tekno's come with their on specially designed Hub Carriers. This means you cant use any after market hub carrier that you might already have installed or plan on buying. I was still using the stock ones so I didn't find it to be of any concern. I have yet to break one yet and they seem common enough on the internet that it wouldn't be hard to get a replacement.

to says its a complete kit it would need 2 more pin also the pin-screw for the c-cup are not inclueded so to be clear if you buy them make sure to keep or have some in stock ..for the toughness of the driveshaft i jumped drop , bash the shit out of it landing on flat concrete from 4-5 foot and YESS i broke many part but the shaft are still 100% staight i wasint expecting that at all !!! that why i give 5 star

The picture shows pins.