SANWA JLF-TP-8YT Joystick Red Original - for Arcade Jamma Game 4 & 8 Way Adjustable, Compatible with Catz Mad SF4 Tournament Joystick (Red Ball Top), Use for Arcade Game Machine Cabinet S@NWA

This is a very good joystick for 4-8 way arcade consoles. I installed it in my DIY 412-in-1 vertical shooter cocktail table, and it works very well. Easy install to JAMMA harness. 4-to-8 way restrictor easy to switch during installation (remember to go easy on the tabs!)

Nice joysticks. Legends Ultimate owners need to know these are not directly swappable for stock ALU sticks. You will need to pull the mounting plate off the old sticks as the holes don't line up. You may also want to pull the shafts out of the old sticks and use them in these...if not understand the stick will be half the height above the deck. I just left it that way and will see if it is an issue. Springs were a little firmer than stock sticks and they feel more solid. I went ahead and put 2 lb springs in while I had them apart anyway.

Due to the issues with a joystick on both of my Arcade1up machines I have now put one of these in two different Arcade1up machines (Mortal Kombat and NBA Jam). They feel kind of similar to the stock sticks but there is certainly a quality difference. The clicking is a little quieter and less cheap sounding than the stock sticks in the Arcade1up cabinets. It comes set up as 8-way but can be switched to 4-way if u are using it for Pac-Man or something like that by adjusting the retainer on the bottom of the stick. It’s pretty easy to do but you have to take the control deck off to access the bottom of the joystick. I like the standard square 8-way gate and even don’t mind the light tension springs for the NBA Jam but hate both in the MK. I put an octagonal gate on the one in the Mortal Kombat machine and love it. I plan on putting 4 lb tension springs in the MK cabinet and maybe 2 lb springs in the NBA Jam (just so it dosnt feel so cheap). As far as install goes, you have to be somewhat handy, but it’s pretty easy to install. You will want to take the metal plate off of your stock Arcade1up joystick and install it on your new sanwa. This way the screw holes match up and you don’t have to make a bunch of new holes. The other thing is this joystick comes with a 5 pin connector and the 1up has 8 wires soldered in. This is where you may spend a little extra time figuring it out. Basically, under your joystick, there are four switches/buttons (up, down, left, right). On the stock setup, each switch is connected to the control board with two wires (power and ground). To wire in the new joystick, you just have to use the included connecter and splice 5 wires. You will use the positive wire from each switch and connect to one of the four colored wires on the connecter. You can use just one of the old grounds and connect it to the black wire on the included connecter. You could solder the wires, but I just twisted and used heat shrink tubes and a heat gun. Electrical tape would work fine too. A little trial and error may be needed to have your directions correct if your like me, but the second time was a lot easier. Size wise the sanwa is about the same as the Arcade1up sticks so the only issues fitting should be able to be resolved by orienting the stick so the 5 pin connecter isn’t obstructed. I will try to add pictures if I do another one or when I do the springs.

Very well made Joystick by a well known arcade controller parts manufacturer. This company is the best quality wise for parts like this. I used mine along with Sanwa's black arcade buttons to build my own controller for street fighter 5 and it worked very well. Building a controller with separate parts like this really adds to the personality of the controller. You can build it exactly to your liking with the colors that you want and with whatever wood/metal/shoeboxish material that you like. You can even just throw it into a pre made plastic box and it would still work very well. As for this actual stick, it feels very satisfying when the stick reaches the registration distance for the movement. It feels akin to using cherry mx blue keys on a mechanical keyboard: Clicky. I've tried out my friend's stick that costed him only $15 from another manufacturer, and I've got to say that it just doesn't feel as good. It feels very muddy and the transition just doesn't feel as satisfying. This is stick is definitely worth the extra money and will probably live for a lot longer. It also comes in a lot of different colors, so you can pick and choose from whatever fits your style. At the end of the day, it really makes it a lot more enjoyable to use something like this as opposed to a normal controller, just to get that true genuine arcade feeling while still being super accessible in your own home.

I bought this to swap in my 8bitdo arcade stick. Simple swap but I heard and felt something weird when moving the stick around after the initial installation. The square gate that comes with this stick is adjustable to swap between 4 and 8-way. The piece that rotates in the gate is able to move a tiny amount. I could feel it and hear it. Thankfully the square gate that comes with the 8bitdo is compatible with this Sanwa stick. If this came with a solid plastic gate it would get 5 stars.

Excellent joystick! Had tried other brands and they were disappointing! So far no complaints with this joystick, works great!

Excellent joystick. Very durable and lasts long.

Installed it on my mayflash 500 and it works wonderful.