Epoxy Instant Mix, Translucent Yellow 5 Minutes, 0.47 fl oz Syringe, Pack of 2

Easy to use. Not a lot of pressure required to deliver the mixed fluids through the special syringe tube. Used it on a sockslide which is supposedly made out of ABS plastic. It's been working just fine, the glue is holding very well.

I can't speak to other applications but this was exactly what I was looking for. I needed a strong epoxy which would flow well into crevices but was thick enough not to run all over, this is about the consistency of cold maple syrup upon dispensing but hardens within a few minutes to tacky and then starts to solidify. I had a barrel shaped wiring harness with a number of wires close together, which would move and touch each other at extremes. I applied the epoxy to the wire ends, which were soldered in place, and then wrapped tape around the area to make a tube and then filled the area to make a solid epoxy plug. I did it once and let dry for a few hours and then did the process again. The result was exactly as desired, all the wires are encased in epoxy and the strain relief slides over the epoxy plug. The epoxy resin cures up very hard in 24 hours but it does not seem to be brittle. It fills gaps well and is not difficult to work with. If I was using this for any other application, I would ensure the work I wanted to connect was sanded and de-greased, to provide the epoxy something to grip onto. Perhaps this is the problem some folks are having who have rated this product low. I found it perfect for my needs.

No tools required, great size for getting nozzle into hard to reach places. Syringe has a snap off top and the nozzle screws onto the syringe. This joint is pretty shotty and can blow out if you apply too much pressure. Gentle pressure and ensure bracing or pressure of glued parts, a blow dryer speeds drying time. Great glue, crappy syringe.

Working is great

(*Updated on 26 Feb '23*) I've used this on about a dozen (maybe 2 dozen-ish) different projects since I purchased it about 18 months ago and used it on different craft mediums. I've come to the conclusion that the only con is what I wrote when I purchased it: It takes longer than 5 minutes to set (ie set enough to not have to hold pressure yourself). A few pointers: 1- Purchase this product. (No, really. Purchase it. It's THAT good.) 2- The colder the product, the more difficult it is to work with. As such, trying to push it out with the "syringe"/plunger proves to be frustrating. 3- Immediately after you apply the epoxy, before you even adhere the objects together, pull backwards on the epoxy plunger. This will, so long as you pull the plunger back far enough, prevent the epoxy from spilling out of the tip and gunking up the lid. 3- (No time recommendation here) Use a warm, wet ("wrung-out" wet not dripping wet) cloth to clean up any tip seepage before you close the epoxy "syringe". 5- Give a shout out to Dr. Sylvan O Greenlee for inventing liquid epoxy. 6- Use the epoxy. 7- Run out of said epoxy. 8- Repeat Steps 1 - 7 as needed. (Original review directly below and prior to the 26 Feb '23 update this had a 3/5 🌟 ranking. Update includes changing that to a 5 out of 5🌟s.) Pro: A little goes a long way Con: It takes longer than the 5-minute set time it professes. TIP: If possible, clamp your pieces together to ensure successful adherence.

This stuff works. Extremely well!!! It dries fast and will dry clear. The directions were super easy and I was very happy that my broken cow statue is standing again. Make sure you follow the instructions and you won’t have any problems at all! The adhesion is powerful! It holds very well and I am happy how affordable this product is I did buy the two pack and used them both. It was the perfect amount! I do admit that the pusher can be kind of hard to pull the epoxy but it’s manageable! There could very well be an easy fix to that. Make sure you get the air bubbles out before starting. Follow the directions.

This epoxy works well and hardens fast. The plunger is a horrible design. First, there is nothing to keep the plungers even while depressing them. You don't get an equal amount of the two parts unless you are very careful. The package tells you to slightly pull back on the plungers after use, but there is nothing to hold the plungers in and they can pop out. The two plungers are not color coded, nor is the syringe, so you can end up putting the plungers back in the wrong way. I assume that will epoxy the plungers into the syringe. The cap that they give you to put on the syringe after use is almost impossible to put on. I had to hold it with a pair of pliers and push really hard to get it to snap into place. You get two nozzles and they tell you to throw away the nozzles after use. All that epoxy and they expect you to only epoxy two things. I didn't bother using the nozzle and just mixed the epoxy myself using a wooden coffee stirrer. the epoxy did set fast and seems to be very strong so far. But, save yourself a mess and hassle. Just get the epoxy in two separate squeeze tubes and forget about trying to use a plunger package.

This stuff is great. I used it to fix the rear diff bushing in my 350z

Takes a full day to set but works great for fixing artificial jewellery

Muy buen pegamento, muy buena calidad, solamente que es muy difícil volverlo a utilizar ya que, aunque quites la pipeta y le coloques la tapa es dificilisimo volverlo a utilizar. Hay que dejarlo secar por lo menos 12 hrs y listo, transparente 👍🏻

Its not that strong glue what i expect to be , but is doing the job.

Quickness of sealing Used to attach metal lamp to cement base.

Sehr zu empfehlen. Gut für unterwegs.