4Button Flip Folding Remote car Key Shell for Chevy Cruze Epica Lova Camaro

I had some difficulty winding the spring that flips the key out. Unlike the original fob it has a split cover that facilitates replacing the battery. It comes with the Chevrolet logo so you don’t have to use the one on the original case.

Make sure you're mechanically inclined to install these. They work well and revived my worn out keyfob. This is made in China and not OEM so you will have to push the PIN out to release the key of the metal arm on the fob. You cannot use the oem one unless you want the switch button to sink into the fob. Look for Google guides to help with install. I used a watch kit to separate the key, then a hammer to push the OEM pin through the hole that connects the key to the arm. The rest should be in the included instructions. Good luck!

I would have given it a higher rate , but it did not fit. Everything on it was perfect except the silver button to release the key. the one that came with it was smaller and had a different design than the one that was on my original key. And I was unable to use the key release button from my original key because it was to large to fit in the new fob. It says that it works for the 2014 model sonic but that was a lie.

Great case! My fob was falling apart. Buttons coming out. wrapped it with electrical tape to keep it together. only made it worse. I successfully replaced the original case with this one. It was a little difficult though. I had to remove the keyblade from the original hinge/button. Hardest part was getting the original case open with out destroying the circuit board. I would recommend this to anyone looking to replace a mangled fob. Just know that it's probably gonna be bit of a pain in the butt.

Works well, except for the latching feature. My OEM parts won't fit because the hole for the button in this housing is too tight. Key doesn't stay latched in the closed position very well.

The replacement I needed

It was just a little difficult removing the new roll pin. And reinserting the roll pin with my old key was a little difficult also. But mission accomplished. High quality replacement. Thanks.

Perfect look and feel and internal board swap a perfect fit - i opted to attempt to Swap my original key with the blank key and that’s where i had a problem - the key length itself is exact, no issue there. It is in the part where you have the button inserted into the pre cast form on the key- simply , the old button works with the old key-the new button works with the new (blank) key- Yet the old button does not work in the new key (blank) .. The included blank key hole where the button drops into is significantly thicker than the original key and original button.. can NOT swap old key to new case - the original button will sit to flush to the case and unable to push to spring the key out.. Attempted to use the new button in original key and that also does not fit.. the internal area of the new key is much thicker than the original.. so not compatible.. my only option now is to get the new blank key cut.. one note - a number stamped on the top of the new key is “2” .. the number stamped on the Top of original key is “1” What that means I’ve no idea Yet they are not compatible..

Worked great for my 2014 Chevy Cruze. Everything fit properly

Really liked received quickly. HOWEVER, fob was slightly different (smaller) than fob I needed to replace. Had to cut small pieces from covers....small screw very difficult to install and key doesn't retract in this new fob. After an hour or more, I now have a fob that could come apart (small screw not fully inserted)....key stuck open (not retracting) and this fob for my 2014 Chev Cruise is not a correct fit. BUt, because of low cost and alterations I needed to make, will not be returning it. Not sure how long it would long work. Overall, my experience with Amazon has been very positive. I guess this fob will, hopefully, will be my first and last negative review.

A pin for unpin the pin of the original key is needed because the supplied key "gear" does not fit the original one... so you have to dismount the metal key part as well

I had to destroy my original key with screwdrivers ,pliers and soldering iron (40 min work). I put my old blade in the new and it works. But blade looks stuck and i have to manually push it to come, but it retracts well. Overall Good Product and match perfectly chevy cruze 2011

le prix