⚡ Blast Through Rust Like a Pro – Compact Power, Maximum Impact!
The 8MILELAKE Compact Air Needle Scaler delivers industrial-strength cleaning with 12 hardened steel needles operating at 4000 BPM. Designed for professionals, it efficiently removes rust, weld slag, paint, and dirt using just 4 CFM of air at 90 PSI. Its lightweight carbon steel build and compact size make it the go-to tool for precision surface prep on the go.
| Manufacturer | freebirdtrading |
| Item Weight | 2.57 pounds |
| Product Dimensions | 4.13 x 2.17 x 1.38 inches |
| Is Discontinued By Manufacturer | No |
| Material | Carbon steel |
| Item Package Quantity | 1 |
| Batteries Included? | No |
| Batteries Required? | No |
C**E
Works Great
Rust doesn’t stand a chance. Made quick work of a big job.
A**G
Better than most on the market
I’ve had this for over a year now. Use it to knock off concrete on the ready mix truck I drive. Compared to the ones that the company provides us that cost anywhere from $200-$400, this one has outlast and out preformed them easily. No needles have fallen out or broken which has been the issue with the one the company provides us. It’s not big and bulky like others either. After using this one for 30 minutes continuous, your hand and wrist aren’t sore from use. Use it for hours on end and no issues.
G**E
Nice air scaler
I've only used it a couple of times but it seems to be of very good quality workmanship and works just fine. Not overly lengthy or heavy. I think it's a good value.One thing to be aware of, and no fault of the scaler. A 1/4" air connector came with it in the box. I wasn't sure which part to unscrew to install it, so the first thing I unscrewed was the large nut on the end of the scaler. The opening was too large for the 1/4" connector. Thinking it should have fit, so I looked a little closer. On the end of the large nut, is a thin, knurled disk. THAT is what you need to unscrew to install the 1/4" connector! It is threaded to match the 1/4" air connector. I screwed the 1/4" connector into the large nut, and then the large nut back into the scaler....success! The large nut goes in without leaking, but I had to use teflon tape on the 1/4" one to get a good NPT thread seal...pretty much standard for an air fitting.
R**K
Durable
Durable
J**T
Works great
Works great
J**S
Good quality
It was great worth the momey
D**Z
You get what you pay for
I am a snob when it comes to air tools. This thing leaks a lot of air so take it off when you're not using it. I have a pile of stuff from various makes/models of air tools from air cat, snap-on, and even harbor freight's "high-end" stuff. I solely bought this to unstick a lifter from an LC9 LS engine in a yukon, and have no need for the scaler part. It got the lifter unstuck but thought I'd give it an honest review. It hammers and works, but if you need a real tool, look elsewhere. I would expect the internal valve to leak quickly and it will need replaced within a year or two depending on use. I only picked this model due to the referral supporting a YT guy who posted a convenient link on his guide video.
H**.
Inspect needle scaler thoroughly before use
First of all when I open the package the needle gun was out of the box. Then when I pop the protective cap off the air Inlet it had rust and some sort of oxidation clogging the screen. Not looking good so far. Update, I tried using this needle scaler and it would not work at all upon further inspection the entire inside of the thing is packed full of rust and some sort of grit. Extremely disappointed.
ترست بايلوت
منذ أسبوعين
منذ شهر
